Bosch DISHWASHER Bedieningsinstructies - Pagina 14

Blader online of download pdf Bedieningsinstructies voor {categorie_naam} Bosch DISHWASHER. Bosch DISHWASHER 24 pagina's. Dishwasher bosch
Ook voor Bosch DISHWASHER: Gebruiksaanwijzing (30 pagina's), Handleiding voor installatie-instructies (34 pagina's), Gebruiksaanwijzing (30 pagina's), Gebruiksaanwijzing (28 pagina's), Gebruiksaanwijzing (30 pagina's), Gebruiksaanwijzing (38 pagina's), Gebruiksaanwijzing (42 pagina's), Gebruiksaanwijzing (32 pagina's), Gebruiksaanwijzing (36 pagina's), Gebruiksaanwijzing (30 pagina's), Gebruiksaanwijzing (24 pagina's), Gebruiksaanwijzing (26 pagina's), Gebruiksaanwijzing (40 pagina's), Gebruiksaanwijzing (28 pagina's), Gebruiksaanwijzing (29 pagina's), Gebruiksaanwijzing (28 pagina's), Gebruiksaanwijzing (28 pagina's), Gebruiksaanwijzing (28 pagina's), Handleiding voor installatie-instructies (50 pagina's), Handleiding voor installatie-instructies (20 pagina's), Gebruiksaanwijzing (36 pagina's), Gebruiksaanwijzing (25 pagina's), Gebruiksaanwijzing (46 pagina's), Gebruiksaanwijzing (31 pagina's)

Pagina afdrukken
Bosch DISHWASHER Bedieningsinstructies
aus

Washing the dishes

A qua sensor *
A q u a s e n s o r
* depending on model
The Aqua sensor is an optical measuring
device (light barrier) which measures the
turbidity of the rinsing water.
The Aqua sensor is used according to the
programme. If the Aqua sensor is active,
"clean" rinsing water can be transferred to
the next rinse bath and water consumption
can be reduced by 3–6 litres. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In the
automatic programmes the temperature
and running time can also be adjusted to
the degree of soiling.

Switching on the appliance

– Turn on the tap fully.
– Close the door.
– Switch on ON/OFF switch (.
The Cleaning display )" flashes.
– Rotate programme selector 8
to the required programme.
– Press START button @.
The Cleaning display )" is lit. The
programme starts running.
T imer programming *
T i m e r p r o g r a m m i n g
* depending on model
You can delay the start of the programme
by 3, 6 or 9 hours.
– Switch on ON/OFF switch (.
– Keep pressing the Preselected starting
time button H until the appropriate
display 3h, 6h or 9h is lit.
– Press START button @, timer
programming is activated.
– To delete the preselected starting time,
keep pressing the Preselected starting
time button H until none of the
displays 3h, 6h or 9h is lit.
You can change your programme
selection at any time until the
programme starts.
14

End of programme

The programme has ended when neither
of the two displays h or )" is lit.
Note
To save energy, the dishwasher
automatically switches off after the end
of the programme.

Interrupting the programme

– Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave the
door ajar for several minutes and then
close. Otherwise, expansion (pressure)
may cause the appliance door to
spring open or water to run out of the
appliance.
– To continue the programme, switch on
the ON/OFF switch ( again.
T erminating the programme
T e r m i n a t i n g t h e p r o g r a m m e
(Reset)
– Press START button @ for
approx. 3 sec. until all displays go out.
– The remaining programme sequence
for draining the residual water takes
approx. 1 minute.

Changing the programme

When the START button @ has been
pressed, the programme cannot be
changed.
The only way a programme can be
changed is by Cancel programme (Reset).