Electrolux EFLW317TIW Gebruiks- en onderhoudshandleiding - Pagina 31
Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} Electrolux EFLW317TIW. Electrolux EFLW317TIW 32 pagina's.
Ook voor Electrolux EFLW317TIW: Handleiding voor installatie-instructies (44 pagina's)
Pagina afdrukken
Avoid Service Checklist, continued
OCCURRENCE
POSSIBLE CAUSE
WATER
Water collects in folds
This is a result of the washing
of the door gasket at
action and is part of the normal
the end of the cycle.
operation of the washer.
Water collects in
This is a result of the siphoning
bleach and fabric soft-
action and is part of the normal
ener compartments.
operation of the washer.
Wash load too wet
Washer is overloaded.
after spin.
Load is too small.
Load is out of balance.
Drain hose is kinked.
Water does not enter
Water supply is not adequate in area.
washer or it enters
slowly.
Water supply faucets are not com-
pletely open.
Water is being used elsewhere in
the house. Water pressure must be
at least 30 psi (260 kPa).
Water inlet hoses are kinked.
Water inlet screens plugged.
Warm or hot water is
Hot water heater is set too low or is
not hot enough.
a distance from washer.
Hot water is being used elsewhere
in the house.
Water in washer does
Drain hose is kinked or clogged.
not drain or drains
Drain hose standpipe is too tall.
slowly.
Maximum standpipe height is 8'
(2.4 m).
House drain pipes are clogged.
Water leaks.
Fill hose connection is loose at
faucet or washer.
Dispenser drawer not completely
closed
Oversudsing.
Wrong detergent.
Too much detergent.
Incorrect wash and
Hot and cold water hoses are con-
rinse temperatures.
nected to wrong supply faucets.
Center display will
alert this condition
with "HOSE" alarm.
See Other Features for
more information.
Water is entering
Drain hose standpipe is too low.
washer but tub does
Standpipe must be a minimum
not fill.
of 23.6" (60 cm) high to prevent
siphoning.
Solutions to Common Inquiries
SOLUTION
Water may be removed by removing the
dispenser drawer (see Care and Cleaning in
this guide) and draining water into the empty
drum or sink.
Do not overload washer. See Operating Your
Washer, step 4.
Add 1 or 2 similar items to help balance the
load.
Rearrange load to allow proper spinning.
Straighten drain hose.
Check another faucet in the house. Wait until water
supply and pressure increase.
Fully open hot and cold faucets.
Avoid running water elsewhere while washer
is filling.
Straighten hoses.
Remove hose from inlets and clean screens.
Measure hot water temperature at nearby
faucet with candy or meat thermometer. Water
temperature should be at least 120°F (49°C).
Adjust water heater as necessary.
Avoid using hot water elsewhere before or
during washer use. There may not be enough
hot water available for proper cleaning. If
problem persists, your hot water system may
be unable to support more than 1 use at a
time.
Clean and straighten the drain hose.
Reduce standpipe height to less than 8' (2.4
m). See INSTALLATION INSTRUCTIONS.
Unclog drain pipes. Contact plumber if neces-
sary.
Check and tighten hose connections. Install
rubber sealing washers provided.
Close dispenser drawer completely.
Run rinse cycle. Use a low-sudsing, high ef-
ficiency detergent.
Run rinse cycle. Use less detergent in future
loads.
Connect hot water hose to hot water faucet
and cold water hose to cold water faucet.
Increase standpipe height to at least 23.6" (60
cm). See INSTALLATION INSTRUCTIONS.
31