Bosch 2 Gebruiksaanwijzing - Pagina 5

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Bosch 2. Bosch 2 8 pagina's. Mini blender
Ook voor Bosch 2: Snelle installatiehandleiding (16 pagina's), Handleiding voor installatie en gebruik (18 pagina's), Originele handleiding (13 pagina's), Originele handleiding (22 pagina's), Gebruiksaanwijzing (32 pagina's), Gebruikershandleiding (28 pagina's), Gebruikershandleiding en installatie-instructies (16 pagina's), Gebruiksaanwijzing (42 pagina's), Gebruiksaanwijzing (8 pagina's), Gebruiksaanwijzing (12 pagina's), Snelstarthandleiding (2 pagina's), Snelstarthandleiding (9 pagina's), Gebruiksaanwijzing en installatie-instructies (36 pagina's), Gebruikershandleiding en installatie-instructies (48 pagina's), Gebruiksaanwijzing (26 pagina's), Snelle referentiehandleiding (2 pagina's), Gebruikershandleiding en installatie-instructies (24 pagina's), Gebruiksaanwijzing (42 pagina's), Informatie voor gebruik (28 pagina's), Gebruikershandleiding (40 pagina's), Gebruikershandleiding en installatie-instructies (35 pagina's), Gebruikershandleiding (24 pagina's)

Bosch 2 Gebruiksaanwijzing
Individual settings
Function buttons
The spin speed and temperature can be changed before and during the selected
programme. The effects depend on the programme progress.
Temp.°C
You can change the displayed washing temperature. The maximum washing temperature
that can be selected depends on the programme that has been set.
rpm
(spin speed //
(Rinse stop = no final spin))
You can change the spin speed shown or select
laundry remains in the water after the last rinse, display panel - - - -). The maximum selectable
spin speed depends on the model and on which programme is currently selected.
Ready in
When you select the programme, the relevant programme duration is displayed. You can
delay the start of the programme before it begins. The "Finished in" time can be set in
increments of one hour up to a maximum of 24 hours. Press the Ready in
repeatedly until the required number of hours is displayed (h = hour).
Press Start/Pause
.
Option buttons
Programme overview, page 7
SpeedPerfect
For washing in a shorter time with a washing result comparable to that
of the standard programme. Maximum load
Programme overview, page 7.
EcoPerfect
For saving energy with a comparable washing effect to the standard
programme.
Rinse Plus
Additional rinse cycle. For areas with very soft water or for further
enhancing the spin result.
Childproof lock
You can lock the washing machine to prevent the functions you have
on the display panel
set from being changed inadvertently.
ON/OFF: after the start/end of the programme, press and hold the
Start/Pause button for approx. 5 seconds.
Note: The childproof lock can remain activated until you wish to start
the next programme, even after switching off the machine.
Then you can deactivate the childproof lock before starting the
programme and activate it again as necessary once the programme
has started.
Start / Pause
To start, pause and continue the programme and to activate/deactivate the childproof lock.
(Rinse stop (Spülstop) = no final spin,
button
5
Individual settings
Signal
1. Activate the setting mode for the signal volume
To activate the
setting mode
set to
2. a) Set the volume for button signals( depending on model)
rpm
press repeatedly until
the desired volume is
reached
2. b) Set the volume for information signals
turn one
position to
the right

Information on the display panel

:
Turn the (cold water) tap on fully;
supply hose kinked/trapped;
water pressure too low; service, clean the filter
:
Detergent solution pump blocked; service, clean the detergent solution pump
page 10.
Drainage hose/waste pipe blocked; service, clean the drainage hose at the siphon
page 10.
Water in the base tub, appliance leaking. Turn off the tap. Call the after-sales service.
:
Childproof lock active; Deactivating
Switch off the appliance, wait for 5 seconds and switch it back on again. If the display
Other
displays
appears again, call the after-sales service.
rpm
rpm
+
press and
turn one
press and hold for a
hold
position to
further 5 secs until the
the right
display elements light up;
setting mode is activated
set to
to exit the setting
or
mode for the signal
volume
rpm
press repeatedly until the
set to
to exit the
desired volume is
setting mode for the
reached
signal volume
depending on model
page 10,
page 5.
6