DSC Envoy NT9010 Gebruikershandleiding - Pagina 17

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} DSC Envoy NT9010. DSC Envoy NT9010 20 pagina's. Demo stand
Ook voor DSC Envoy NT9010: Installatie-instructies (4 pagina's)

Pagina afdrukken

Announcement:

Problem and how it should be addressed:

"Device low battery,

Your system has detected that one or more of the wireless

press [7]."

detectors on the system has a low battery. Press

tem will announce which devices have a low battery. Change

the relevant batteries. See page 26 for instructions. If this does

not correct the problem, call for service.

"The time and date

If all power to the system is interrupted (AC and battery), the

are incorrect."

system clock and date will need to be reset. See Setting the

Time and Date on page 21. If you are unsure of the cause of

the system power failure, call for service.

Testing Your

Test your system every week. Report any problems immediately to your installation

System

company.

NOTE: Perform system tests during off-peak hours, such as early morning

or late evening.

1. If your system has remote monitoring, call the central station to tell them that

you are testing your system.

2. Begin with the system turned off. Press

sounds the siren and turns on all keypad lights for two seconds. When the

sounder and keypad test is complete, press

3. To test each area of your system, open each door and window in turn, or walk

in motion detector areas.

4. Press the Status button. The system will announce all open zones.

5. If the system has any fire zones, activation will cause the alarm to sound in a

pulsed mode. To silence the alarm, press

CAUTION: Do not use an open flame or burning materials to test a smoke

or heat detector. Contact your installer for information on safe methods of

testing detectors.

6. When you are finished testing the system, inform your central station. If the

system did not work properly, contact your installer.

NOTE: Some features described above will not be functional unless

enabled by your installer. Ask your installer which features are functional

on your system.

Allowing

From time to time, your installer may need to send information to, or retrieve

Computer

information from your security system. Your installer will call your system over the

Access to Your

telephone line using a computer. You may need to prepare your system to receive

System

this "downloading" call. To do this:

1. Press

[Master code]

depending your installer's set up. During this time, the system will answer

incoming downloading calls.

For more information on this feature, please ask your installer.

, and the sys-

[Master Code]

. The system

. This allows downloading for 1 or 6 hours

Tu r n in g Y o u r S ys t em O n (A r m in g ) an d O f f ( Di sar mi n g)

NOTE: Pressing

will only turn on the system. To turn the system off,

you must enter a valid [access code]. See Turning Off Your System on page

10.

Turing On

If you want to turn on the system, and no one else will be entering, you can

Your System

remove the entry time from zones that normally have one. If somebody enters

with No Entry

through any zone, the system will sound an instant alarm.

Time

1. Check that your system is ready (green Ready light is ON)

2. Press

, then your [access code].

• The red (Armed) light flashes as a reminder that the system is on and has

no entry time.

• The keypad sounds fast beeps.

3. The system is now in Stay mode.

Turning On

Your installer may have set up your system to turn on at a pre-set time. If auto-

Your System

matic arming has been set up, when the system reaches the pre-set autoarm time,

Automatically

the keypad buzzers will sound for one minute.

(Automatic

During this one-minute warning time, you may be able to stop automatic arming

Arming)

by entering your [access code]. Ask your installer for more information.

Your installer may have set up the system so that users with a master code can

change the autoarm time at the keypad. If so, master users will be able to turn the

automatic arming function on or off, and program the time at which the system

will automatically turn on each day.

To turn automatic arming on or off:

1. Press

, then [master code].

2. Press

to turn automatic arming on or off. The keypad will beep 3 times

when auto-arm is turned ON, and once when it is turned OFF.

3. When you are finished, press

To change the autoarm time:

1. Press

, then [master code].

2. Press

3. Enter the autoarm time using the 24Hr format (0000 - 2359). For example, to

set the time for 1:00pm, enter (1300).

5. When you are finished, press

NOTE: The system must have the correct time and date in order for the

autoarm feature to work. Please seeSetting the Time and Date on page 21.

twice.