Attwood Tsunami 4606 Installatie-instructies

Blader online of download pdf Installatie-instructies voor {categorie_naam} Attwood Tsunami 4606. Attwood Tsunami 4606 2 pagina's. Attwood tsunami bilge pump installation instructions

Pagina afdrukken

Tsunami Bilge Pump

4606, 4608, 4612, 4613 Series

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69390 Rev. A

WARNING

Read all instructions carefully before installing and using this product.

To prevent personal injury, disconnect the power source when installing

or servicing this product. Always remove the boat from the water before

using 120V AC power tools.

DO NOT use pump to remove gasoline, oil or other flammable liquids.

Always use the fuse amperage rating specified for your pump model.

Failure to do so could result in serious personal injury or fire hazards.

Attwood bilge pumps are designed to exhaust STANDING WATER

ONLY. They are not intended to prevent rapid accumulation of

on-board water due to rough weather, hull damage, and/or other

unsafe navigational conditions.

Refer to Specification Chart to be sure you have selected the

proper pump:

12-Volt Models

ABYC Specifications

(GPH = Gal. Per Hour)

0 ft.

Part

Outlet

Head

Num./

Hose Motor Amp GPH/

Series

I.D.

Cart.

Fuse amps

4606/600 3/4"

4620 2.5A 500/1.5 400/ 1.5 250/1.5 1705/1.3 1250/1.3 8'/27

4608/800 3/4"

4622 4A

800/3.0 660/3.0 510/3.0 2840/2.5 2274/2.5 14'/33

4612/1200 1-1/8" 4624 5A

1200/3.5 900/3.5 700/3.5 4169/3.0 3000/3.0 11' 7"/28

24-Volt Models

ABYC Specifications

(GPH = Gal. Per Hour)

0 ft.

Part

Head

Num.

Amp GPH/

Series

Fuse amps

4609/800 3/4"

4623 2A

800/1.3 660/1.3 500/1.3 2842/1.1 2160/1.1 14'/31

4613/1200 1-1/8" 4625 2A

1200/1.5 900/1.5 725/1.5 4100/1.3 3100/1.3 11'/28

MATERIALS REQUIRED

• Three #8 stainless fasteners, suitable length for mounting surface

• Cordless drill and 1/8" (3mm) bit

• Hose clamps (Attwood # 9185, 2 per connection)

• Mounting pad: marine plywood, fiberglass cloth and resin

• Manual (# 7615A) or automatic float switch (#4201 or 4202)

• Fuel-resistant, reinforced smooth bore outlet hose

INSTALLATION LOCATION

1. Position pump in the lowest accessible part of the bilge. On

sailboats, location should be centered over keel. (Figure 1)

ISO Specifications

@13.6 VDC

@12 VDC

(LPH = Liters Per Hour)

3.3 ft

6.7 ft

0kPa

10kPa

Head

GPH/

LPH/

amps

ISO Specifications

@24.0 VDC

(LPH = Liters Per Hour)

3.3 ft

6.7 ft

0kPa

10kPa

Head

GPH/

LPH/

amps

Figure 1

Base Strainer

10-03

2. Do not mount pump directly to hull. Attach base strainer to a

marine plywood mounting pad that is fiberglassed to the hull.

HOSE CONNECTION INSTRUCTIONS

IMPORTANT: To prevent airlock, hose must rise continually upward

to the thru-hull connector with no dips or sharp bends. Support hose

if necessary.

1. Orient pump outlet for a direct, unobstructed hose path.

2. Secure all connections with hose clamps.

3. If no thru-hull connector exists, install at 12" min. (25mm) above

water line. Apply marine sealant around thru-hull flanges on

interior and exterior of hull.

PUMP MOUNTING INSTRUCTIONS

1. To access mounting holes, remove base strainer. Hold housing with

one hand, depress locking tab with other. Twist counter-clockwise

and remove pump housing from base. It is not necessary to remove

motor cartridge for installation. (Figure 2)

Figure 2

Max

Head

([email protected]/

kPa@12v)

Pump Housing

(3) #8 Fasteners

Max

Base Strainer

Head

(ft.@24v/

kPa@24v)

1/8" Pilot Holes

2. Use base as template to mark 3 mounting holes in mounting pad.

CAUTION: Do not drill through hull. Before drilling be sure mounted

pump will be correctly positioned with pump nozzle pointing toward

thru-hull connector. (Figure 1)

3. Remove base. Drill three 1/8" (3mm) pilot holes at marked locations.

4. Replace base. Attach with #8 stainless steel fasteners.

5. Re-attach pump to base. Insert into base, twist clockwise until tab

snaps in and prevents turning. (Figure 2)

WIRING INSTRUCTIONS

Make all wire connections above the highest water level. Use marine

grade wire connectors only. Waterproof all connections with suitable

materials. (Figure 3)

NOTE: Failure to make waterproof connections and fuse pump properly

will void the product warranty.

Thru-Hull Connector

Hose & Clamp

Suitable Mounting Pad

Lock

Unlock

Lock

Motor Cartridge Replacement

Press Tab

To Unlock

12" min. Above

Water Line

Hose MUST Rise

Upward with NO DIP

Unlock

Motor

Cartridge

Tab