Free The Tone ARC-4 Gebruikershandleiding - Pagina 6
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Free The Tone ARC-4. Free The Tone ARC-4 16 pagina's. Audio routing controller
Ook voor Free The Tone ARC-4: Procedures voor firmware-updates (18 pagina's)
Pagina afdrukken
Managing Presets
In Preset mode the ARC-4 can manage presets in two ways.
Bank Mode
Presets (10 presets) are managed in the order of bank numbers (001–200).
Setlist Mode
This mode is used to manage banks in a sequence in your desired order. For
example, the combinations of effects units to be used in a song are compiled
in a bank. Then by serializing these banks in accordance to the order in
which songs are played in live performance (setlist), presets can be managed
on a song-basis. This ARC-4's feature is very useful for live performances.
Switching between Preset and Direct Modes
1. Press the MODE switch.
Each press alternates Preset and Direct modes. In Preset mode the blue
PS LED illuminates and the Display-2 shows the bank number or bank
title.
In Direct mode the red DIR LED illuminates and the Display-2 shows
DIRECT ACCESS.
NOTE
In Preset mode, effect loop's on/off settigs, settings for control and MIDI signal
transmission, etc. are stored in a preset and the memory contents are recalled
by pressing the corresponding PS/L switch. In Direct mode pressing a PS/L switch
can turn on/off the corresponding loop directly.
Storing an Effect Loop Combination
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the preset to which you want to store the
combination.
4. Press the SELECT switch to select "LOOP."
5. Press the ON/OFF 1–8 switch to select the effect loop you want to store.
6. Press the STORE switch to store your selection.
NOTE
Effect loop combinations can be stored even in Direct mode. Select the preset
by following the above steps 1–3 and press the MODE switch to change to Direct
mode. Then press the PS/L switch to select the loop you want to store and press
the STORE switch or BANK /STORE switch to store it.
Recalling a Preset
1. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
2. Use the PS/L switch to select the desired preset.
10
Storing Phase Invert Function (INVERT) Setting in a Preset
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the preset to which you want to store the
setting.
4. Press the SELECT switch to select "FUNC" and to turn on the LED.
5. Press the ON/OFF 5 switch to activate the Phase Invert function (INVERT).
6. Press the STORE switch to store the setting.
NOTE
Some effects units invert (reverse) the phase causing their sound to be buried
in band mix. In such a case turn on this INVERT function to correct the phase of
the signal (to be in phase) before outputting. However intentionally inverting the
phase can sometimes enhance the sound. So please try this function in various
situations. Signal phase can be confirmed with the PHASE ANALYZER/PHA-1
(option).
Storing Boost Function Setting in a Preset
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the desired preset.
4. Press the SELECT switch to select "FUNC" and to turn on the LED.
5. Press the ON/OFF 6 switch to activate the Boost function.
6. Press the STORE switch to store the setting.
NOTE
The boost amount of the signals at the OUT-A and OUT-B terminals can be adjusted
respectively by the BOOST-A and BOOST-B knobs on the rear panel.
Storing Mute (MUTE-A, MUTE-B) Setting in a Preset
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the desired preset.
4. Press the SELECT switch to select "FUNC" and to turn on the LED.
5. Press the ON/OFF 7 or 8 switch to select the output terminal you want to
mute.
6. Press the STORE switch to store the setting.
How to Control External Devices from ARC-4 (Preset Mode)
The ARC-4 can send control and MIDI signals to control a connected external device.
LB-2
C1/C2
The ARC-4 can send four
control signals (latch/
momentary) simultaneously.
C1/C2
Storing Control Terminal Setting in a Preset
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the desired preset.
4. Press the SELECT switch to select "FUNC" and to turn on the LED.
5. Press the ON/OFF 1–4 switch to select the control terminal whose setting
should be stored.
6. Press the STORE switch to store the setting.
NOTE
Regarding the specifications of the connecting cable (monaural or stereo), please
refer to the connected device's spec sheet.
Setting Operation Type of Control Signal to be Sent p.21
Storing MIDI Program Change Number Transmission in a Preset
After connecting the ARC-4 to a MIDI device, preset memories of the
connected device can be recalled. The ARC-4 can send sixteen MIDI program
change numbers suimultaneously by using the MIDI channels CH1–CH16.
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the desired preset.
4. Press the MIDI PC# switch.
5. Press the UP/DOWN switch to select the desired item.
6. Turn the PARAMETER encoder to set the parameter.
7. Press the STORE switch to store the setting.
8. By pressing the MIDI PC# switch, the previous preset display returns.
FT-2Y
The ARC-4 can control up
MIDI IN
to individual sixteen MIDI
MIDI OUT
devices at the same time.
Parameter 1: MIDI channel (Shown as "CH" on Display-1) 01 to 16
Parameter 2: MIDI program change number (Shown as "PC" on Display-1) OFF,
001 to 128
Parameter 3: BANK select (Shown as "MSB" on Display-1) OFF, 000 to 127
Parameter 4: BANK select (Shown as "LSB" on Display-1) OFF, 000 to 127
NOTE
MSB/LSB: This is a message for Bank Select operation. If it is not necessary to
specify, set both MSB and LSB to "OFF" (initial value). The MIDI channel (CH) must
be the same as that of the connected MIDI device.
Storing MIDI Control Change Number Transmission in a Preset
After connecting the ARC-4 to a MIDI device, the connected device's
parameters can be controlled.
1. Press the MODE switch to select Preset mode.
2. Use the BANK /L8 or BANK /STORE switch to select the desired bank.
3. Use the PS/L switch to select the desired preset.
4. Press the SELECT switch to select "CSW(CC#)" and to turn on the LED.
5. Press the ON/OFF switch 1–8 to select the "CSW (control switch)" to be
used.
6. Press the STORE switch to store the selection.
NOTE
The MIDI control change number assigned to a CSW (control switch) can be set in
Edit mode or Preset mode.
Setting MIDI Control Change Number to be Sent p.12
Details of MIDI Data Sent When CSW is Turned On/Off p.29
11