DANLERS CZ HB ND Installatie-opmerkingen - Pagina 2

Blader online of download pdf Installatie-opmerkingen voor {categorie_naam} DANLERS CZ HB ND. DANLERS CZ HB ND 2 pagina's. Controlzapp high bay controls

Pagina afdrukken

DANLERS CZ HB ND Installatie-opmerkingen

Installation procedure

1. Please read these notes carefully before commencing work. In case of doubt please

consult a qualified electrician. Ensure wires and cables are securely held within the

connection terminals.

IMPORTANT: The CZ HB (xx) Control Unit clock battery must be engaged (ON)

prior to installation by switching the RED dip switch (see diagram E) to the

DOWN position.

2. POSITIONING: The CZ HB (xx) switch should be installed to achieve correct

coverage of the area, see diagram B. If the photocell override facility (enabled via

ControlZAPP app) is required, the switch must be located above an area where

daylight can give greater illumination than the artificial light. Avoid locating this

product where it is exposed to drafty conditions (exposed lobbies, open ceiling

voids or near fans) or near heat sources.

3. Disconnect the PIR from the circuit before performing insulation testing of the wiring

circuit.

4. Do not connect on a circuit with large inductive loads, as induced spikes may cause

false triggering or damage the PIR.

5. CZ HB (xx) must be connected to the ControlZAPP Power Supply (CZPS) via the

ControlZAPP communication cable (telejack) provided, for wiring see diagrams C

and D. NOTE: The use of non ControlZAPP connectors may damage the CZ CESR

or CZPS and will invalidate the warranty).

6. Knockout or drill the appropriate holes on the mounting plate for attaching the plate

to the ceiling or back box (if applicable). Feed telejack through the appropriate (side

or rear) entry hole. Screw the back mounting plate to the ceiling or back box via the

mounting holes. Push the telejack connector into the sensor head terminal. Push the

sensor head onto the mounting plate and align the side clips with the slots on the

sensor heads

Settings and calibration

NOTE: ALL settings are adjusted by ControlZAPP App as specified in the

ControlZAPP App User Guide (downloadable from the DANLERS website)

including: MODE settings, SCHEDULER settings and photocell settings and

intelligent photocell calibration procedure.

MODE settings include: Detect Movement (enable or disable), Sensitivity, Short Visit

Mode (with timer), Turn ON automatically (Presence detection or Absence detection),

Turn OFF timeout (from10sec to 23hrs 59min 59sec), Respond to Daylight (enabled

or disabled) the calibration process must be run for the intelligent photocell to work.

Delay before ON or Delay before OFF timers, Scene Recall (ON or OFF).

SCHEDULER settings include:

DAY TYPES (defining times for each of the Modes to occur).

WEEKLY SCHEDULE (defining which Day Types are assigned to different days of the

week).

EXCEPTIONS (defining exceptions to the schedule).

VIEW ON CALENDAR (overview of what and when Modes happen).

A: Detection diagrams

NARROW

SPOT

DETECTION (ND)

DETECTION (SP)

Mounting height

up to 12m

up to 20m

Perspective view -

ceiling mounted

15m

Up to 5m

Up to 3m

diameter

B: Wiring diagram, single PIR

100-260 VAC

50 / 60 Hz

load

D: Mounting plate fixing

Knock out mounting

For telejack entry from

holes or pre-drill

above - knock out

pilot holes.

central mounting hole

E: Connector diagram

IMPORTANT

Red dip switch (MUST be

switched towards centre of control)

to engage clock battery ON

Power Supply

WIDE

DETECTION (WD)

Mounting height

up to 14m

Perspective view -

ceiling mounted

Up to 28m

diameter

C: Wiring diagram, multiple PIRs

100-260 VAC

50 / 60 Hz

Clip telejack into the device

For side entry -

then join device to mounting

knock out side

plate via mounting clips

mounting hole

Control Unit

Telejack connector

load