Daspi JENNY Gebruiksaanwijzing - Pagina 7

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Daspi JENNY. Daspi JENNY 12 pagina's. Gear motor for balanced overhead door

Pagina afdrukken

JennY – Central oPerator

Identify the axis of rotation "A" of the overhead door and

determine a new axis "R" parallel to "A" and passing under it

at a distance of 100 mt (fig. 2).

Install the operator on the plate "P" by screws "V1" and put

it temporarily in the middle of the overhead door aligning

the axis "R" , previously determined, to the driving shafts "C"

which comes out from the gear motor (fig. 3).

Check that the plate "P" is sufficiently long to have more

points of support on the door, otherwise contact the supplier

and ask for a longer plate again.

Take away the operator and fix the plate "P" strongly to

the door by a good welding or with screws, so reinstall the

operator and fix the screws "V1" .

Fix by a good welding the anchorage supports "S" of the

telescopic arms on the superior cross brace of the overhead

door on the sides of the door (fig. 5).

Check that between the overhead door arms and its fixed

sides there are sufficient space for the telescopic arms "B" ,

otherwise contact the supplier and ask for bowed arms.

Install on the supports "S" the telescopic arms "B" using the

screws "V2" without screw it completely to allow the arm "B"

(fig. 6) a correct movement.

Put the door in its maximum opening and cut the components

"Bf" of the arms "B" so that the final part "Bm" if aligned with

the axis "R" put out "Bf" of 100 mm (fig. 8).

Close the door and insert the bushes situated on the end of the

pipes "D" in the operator driving shafts "C" , so insert the pipes

supports "L " more or less in the middle of pipes (fig. 10).

Install the pipes "D" perfectly horizontal and the arms "B"

perfectly vertical, draw up the point of contact (on the internal

part of the door) so cut the pipes part exceeding (fig. 11).

Fix by a good welding the pipes "D" to the part "Bm" of the

arm "B" (fig. 13).

Fix by a good welding or by screws the pipes support "L " at a

distance of aprox. 200 mm from the arms "B" and the safety

grubs "Gr" on the pipes bushes "D" (fig. 12).

JennY – lateral oPerators

Identify a the axis of rotation "A" of the overhead door and a

new axis "R" parallel to "A" and passing under it at a distance

of 100 mm (fig. 2). Install the operators on the plates "P" by

screws "V1" and put them on the right and left sides of the

overhead door, aligned the axis "R" to the driving shafts "C"

that cams out from the operators (fig.4).

Check that the plates "P" are sufficiently long to have more

points of support on the door, otherwise contact the supplier

and ask for longer plates again.

Take away the operators and fix the plates "P" strongly to

the door by a good welding or with screws, so reinstall the

operators and fix the screws "V1" .

Fix by a good welding the anchorage supports "S" of the

telescopic arms on the superior cross brace of the overhead

door on the sides of the door (fig. 5).

Check that between the overhead door arms and its fixed

sides there are sufficient space for the telescopic arms "B" ,

otherwise contact the supplier and ask for bowed arms.

Install on the supports "S" the telescopic arms "B" using the

screws "V2" without screw it completely to allow the arm "B"

a correct movement (fig. 6).

Put the door in its maximum opening and cut the components

"Bf" of the arms "B" so that the final part "Bm" if aligned with

the axis "R" put out "Bf" of 100 mm (fig. 8).

Close the door and insert the bushes situated on the end of the

arms "B" in the operator driving shafts "C" , so fix the safety

grubs "Gr" (fig. 9).

JennY – FInal oPeratIons (

Carry out a manual manoeuvre (see "Emergency or manual

manoeuvre") to verify the correct functioning and if necessary

re-balance the door increasing the counterweight aprox. Of 3

kg. For each side.

Make the circuitry like in the control panel manual and install

the obligatory safety devices. Insert into the space "H" the bolt

"D1" of M4 y fix the protection cover "K" using the longer

screw "V4" for the upper hole and the smaller screw "V5" for

the lower hole (pic. 13).

Install the handle "MS" and fix it with the supplied screw

"VS" (pic. 14). Teach the people intended for the use of the

automation about the controls, safety devices, emergency

manoeuvre and dangerousness deriving from the utilize of

the automation.

Compile the technical booklet and fulfil the eventual obligations

deriving from the regulations in force.

InstallatIon oF eleCtrICal

lIMIt sWItCH kIt

The limit switch in opening stops immediately, when pressed,

the overhead door opening.

The limit switch in closing, when pressed, set a slowing down

of the door for aprox. 3 second and then stop the overhead

door closing. Remove the operator safety cover.

Install in the holes "F" on the operator left and right the limit

switch "Fc" by the supplied screws (fig. 15).

Install the cams "Ca" on the operator driving shafts "C" (fig.

16).

Connect the limit switch contact N.C. to the control panel (see

Instructions of electronic control panel), we recommend to

use cables with different colour for opening and closing to

recognize immediately the limit switches.

With manual manoeuvre close the door until aprox. 300 mm

to the total closing, adjust the closing limit switch cams "Ca"

till it pushes the limit switch.

Restore the automatic functioning and verify the correct

position of the cams and if necessary adjust them further.

Fix the screws "V3" (fig. 16) of the cams "Ca" and re-install the

safety cover as above explained.

We guarantee the correct functioning of JENNY versions only

and exclusively if provided by DASPI and only if combined

with the original control panel.

You have to do the emergency or manual manoeuvre or

during the installation, or only if the automation does not work

properly or if there is no power supply.

Cut off the power supply.

Turn clockwise the handle "MS" until the motor is released,

then open manually the door (pic. 17).

WARNING: In case of 2 lateral operators it is necessary release

booth operators.

In order to re-establish the normal functioning of the

automation, turn the key "MS" anticlockwise.

Switch on the power supply, pay attention that there's nobody

where the gate is moving.

)

both