Dust Right 1250 CFM Instructies - Pagina 4

Blader online of download pdf Instructies voor {categorie_naam} Dust Right 1250 CFM. Dust Right 1250 CFM 4 pagina's. Dust canister filter

Use proper lifting technique and get the
help of another adult to lift the Canister Filter when attaching
it to the Dust Collector. Failure to do so could result in injury.
4. With the help of another adult and with the machine
turned off, lift the Canister Filter to the dust collector outlet
port. Make sure to position the Canister Filter so it won't
protrude too far and so the post for the Handle is oriented
correctly. (You must be able to move the Handle partway
around the Canister Filter once the Handle is installed.)
Align the holes in the Gasket and in the Canister Filter top
with the holes in the Attachment Collar and attach with the
5/16" x 1/2" Flange Bolts. Use the Open Wrench to tighten.
5. Slide the Handle onto the post projecting from the top of the
Canister Filter, lining up the hole for the 5/16" x 3/4" Set
Screw with the flat area on the post. Thread the Set Screw
into the Handle and thread the 5/16" Nut loosely onto the
Set Screw. Use the Hex Wrench to tighten the Set Screw;
then use the Open Wrench to tighten the nut. (The Handle
is used to spin a three-paddle mechanism inside that
dislodges built-up dust from the pleated filter.)
6. Apply the 3mm x 20mm x 49
around the bottom of the Canister Filter. Trim any excess.
7. Fit the Plastic Bag over the bottom of the Canister Filter,
making sure the edge extends at least to the top of the
3mm x 20mm x 49
" Foam Tape. Install the Clamp
3
4
and secure tightly around the Plastic Bag.
Maintenance
> Turn off and unplug your Dust Right 1250 CFM
Wall-Mount Dust Collector before attempting to install
the Canister Filter, emptying or changing the Plastic Bag
and before any maintenance.
> Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
> Periodically inspect dust and filter bags for any cuts,
rips or tears. Do NOT operate the dust collector with
a damaged bag or hose.
> After assembly or maintenance, make sure that you
have removed all loose tools from the machine before
turning it on.
> Empty bag regularly. Do NOT fill the bag more
than half-full.
> Wear safety glasses and a dust mask/respirator while
emptying the bag.
1. With the Dust Collector turned off, move the Handle back
and forth partway around the Canister Filter a couple of times
to dislodge dust that has built up in the pleated filter. Because
the mechanism inside the Canister Filter has three paddles,
you need to move the Handle only one-third of the way
around the canister to cover the entire filter.
4
54818
Rev 03/19
" Foam Tape in the channel
3
4
2. Once the Plastic Bag becomes about half-full, turn off and
unplug the Dust Collector and then release the Clamp to
free the bag for emptying or replacement.
3. Reinstall the emptied Plastic Bag or install a replacement as
described in Step 7 in the Assembly section.
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
5/16" x 1/2"Flange Bolts
Attachment Collar
Gasket
5/16" Nut
5/16" x 3/4"
Set Screw
Canister
Filter
3mm x 20mm x
49
" Foam Tape
3
4
Clamp
Distributed by Rockler Companies, Inc.
Medina, MN 55340
Handle