Dust Right 1250 CFM Instructions - Page 4

Browse online or download pdf Instructions for Water Filtration Systems Dust Right 1250 CFM. Dust Right 1250 CFM 4 pages. Dust canister filter

Print Page

Use proper lifting technique and get the

help of another adult to lift the Canister Filter when attaching

it to the Dust Collector. Failure to do so could result in injury.

4. With the help of another adult and with the machine

turned off, lift the Canister Filter to the dust collector outlet

port. Make sure to position the Canister Filter so it won't

protrude too far and so the post for the Handle is oriented

correctly. (You must be able to move the Handle partway

around the Canister Filter once the Handle is installed.)

Align the holes in the Gasket and in the Canister Filter top

with the holes in the Attachment Collar and attach with the

5/16" x 1/2" Flange Bolts. Use the Open Wrench to tighten.

5. Slide the Handle onto the post projecting from the top of the

Canister Filter, lining up the hole for the 5/16" x 3/4" Set

Screw with the flat area on the post. Thread the Set Screw

into the Handle and thread the 5/16" Nut loosely onto the

Set Screw. Use the Hex Wrench to tighten the Set Screw;

then use the Open Wrench to tighten the nut. (The Handle

is used to spin a three-paddle mechanism inside that

dislodges built-up dust from the pleated filter.)

6. Apply the 3mm x 20mm x 49

around the bottom of the Canister Filter. Trim any excess.

7. Fit the Plastic Bag over the bottom of the Canister Filter,

making sure the edge extends at least to the top of the

3mm x 20mm x 49

⁄

" Foam Tape. Install the Clamp

and secure tightly around the Plastic Bag.

Maintenance

> Turn off and unplug your Dust Right 1250 CFM

Wall-Mount Dust Collector before attempting to install

the Canister Filter, emptying or changing the Plastic Bag

and before any maintenance.

> Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

> Periodically inspect dust and filter bags for any cuts,

rips or tears. Do NOT operate the dust collector with

a damaged bag or hose.

> After assembly or maintenance, make sure that you

have removed all loose tools from the machine before

turning it on.

> Empty bag regularly. Do NOT fill the bag more

than half-full.

> Wear safety glasses and a dust mask/respirator while

emptying the bag.

1. With the Dust Collector turned off, move the Handle back

and forth partway around the Canister Filter a couple of times

to dislodge dust that has built up in the pleated filter. Because

the mechanism inside the Canister Filter has three paddles,

you need to move the Handle only one-third of the way

around the canister to cover the entire filter.

54818

Rev 03/19

⁄

" Foam Tape in the channel

2. Once the Plastic Bag becomes about half-full, turn off and

unplug the Dust Collector and then release the Clamp to

free the bag for emptying or replacement.

3. Reinstall the emptied Plastic Bag or install a replacement as

described in Step 7 in the Assembly section.

Check Rockler.com for updates. If you have further questions, please

contact our Technical Support Department at 1-800-260-9663

or [email protected]

5/16" x 1/2"Flange Bolts

Attachment Collar

Gasket

5/16" Nut

5/16" x 3/4"

Set Screw

Canister

Filter

3mm x 20mm x

⁄

" Foam Tape

Clamp

Distributed by Rockler Companies, Inc.

Medina, MN 55340

Handle