Dynabrade 51582 Veiligheids-, bedienings- en onderhoudshandleiding - Pagina 4

Blader online of download pdf Veiligheids-, bedienings- en onderhoudshandleiding voor {categorie_naam} Dynabrade 51582. Dynabrade 51582 4 pagina's. 11 inch random orbital sander electronic variable speed

Pagina afdrukken
11" Random Orbital Sander – Is a right angle electric hand tool which includes: a variable speed on/off switch; side handle; a RPM Dial which maintains desired RPM, when
under load; and is equipped with an 8 ft. cord set.
1. For optimal performance use only 11" diameter back-up pad (P/N 56231 Back-Up Pad, supplied on tool) and 11-1/4" diameter loop-faced abrasives.
2. With power source disconnected from tool, securely center abrasive on back-up pad. The rated RPM of the accessory must be equal to or greater than the rated RPM of
the tool.
3. Hold tool by the switch handle and the side handle. Do Not hold tool by head/housing assembly. Keep hands away from all sanding edges and moving parts.
4. Tool has variable RPM dial on top side of switch handle. Dial desired maximum RPM.
5. Squeeze variable speed on/off switch on rear handle to run tool. Tool's on/off switch may be used as a throttle to fluctuate RPM. To lock tool in "on" position continue to
squeeze on/off switch and depress side button. Electronic module maintains specified speed under load. To disengage tool when locked in "on" position push on/off switch
inward.
Important: To keep tool safe a preventative maintenance program is recommended whenever portable power tools are used.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model #, Serial # of your tool.
Routine Preventative Maintenance:
• To extend motor life, remove debris from motor every 20 hrs. with compressed air into the air slots.
• Mineral spirits are recommended when cleaning. Do not use on electrical components or clean tool or parts with any solvents or oils containing acids, esters, ketones,
chlorinated hydrocarbons or nitro carbons. Compressed air may be used to remove dirt from electrical components.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• Tool markings and labels must be kept legible at all times, if not, reorder and replace.
• Visually inspect plug and cord for frays, visible damage and signs of deterioration. Damaged or worn components must be replaced by Dynabrade or qualified repair
technician to avoid a safety hazard.
• Check brushes regularly for wear. Unplug tool, unscrew brush caps and ensure brush wear has not reached wear mark. Clean brushes before reassembling, make sure it
slides freely in holder.
• After maintenance is performed on tool check for excessive tool vibration.
• If the electrical components have been disturbed during repair, check for excessive current leakage at 550 volts with a current leakage checker on all screws
and the gear case.
Handling and Storage of Tool and Accessories:
• Use of tool rests, hangers and/or balancers is recommended.
• DO NOT carry tool by cord.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
Model
Motor
Number
RPM
51582
0 - 3,000
51583
0 - 3,000
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date of
purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or replace at
our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have been defective.
Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to
equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as
bearings, brushes, gears, etc., are not covered under this warranty.
Reference Contact Information
Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
© DYNABRADE, INC., 2009
TOOL DESCRIPTION
ASSEMBLY and OPERATION INSTRUCTIONS
MAINTENANCE and ACCESSORY CARE INSTRUCTIONS
Machine Specifications
Max. Motor
hp (w)
Voltage
Current
1.8 (1342)
120 V (AC)
11 Amp
1.8 (1342)
120 V (AC)
11 Amp
One Year Warranty
®
).
Phase
Frequency
1
60 Hz
1
60 Hz
PRINTED IN USA
Weight
Length
Pound (kg)
Inch (mm)
11.8 (5.35)
21 (533)
13.1 (5.94)
22 (559)
DYNABRADE
Height
Inch (mm)
7 (178)
7 (178)
®
PD09.30