Dynabrade 51582 Руководство по безопасности, эксплуатации и техническому обслуживанию - Страница 4

Просмотреть онлайн или скачать pdf Руководство по безопасности, эксплуатации и техническому обслуживанию для Сандер Dynabrade 51582. Dynabrade 51582 4 страницы. 11 inch random orbital sander electronic variable speed

Печатать страницу

11" Random Orbital Sander – Is a right angle electric hand tool which includes: a variable speed on/off switch; side handle; a RPM Dial which maintains desired RPM, when

under load; and is equipped with an 8 ft. cord set.

1. For optimal performance use only 11" diameter back-up pad (P/N 56231 Back-Up Pad, supplied on tool) and 11-1/4" diameter loop-faced abrasives.

2. With power source disconnected from tool, securely center abrasive on back-up pad. The rated RPM of the accessory must be equal to or greater than the rated RPM of

the tool.

3. Hold tool by the switch handle and the side handle. Do Not hold tool by head/housing assembly. Keep hands away from all sanding edges and moving parts.

4. Tool has variable RPM dial on top side of switch handle. Dial desired maximum RPM.

5. Squeeze variable speed on/off switch on rear handle to run tool. Tool's on/off switch may be used as a throttle to fluctuate RPM. To lock tool in "on" position continue to

squeeze on/off switch and depress side button. Electronic module maintains specified speed under load. To disengage tool when locked in "on" position push on/off switch

inward.

Important: To keep tool safe a preventative maintenance program is recommended whenever portable power tools are used.

• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model #, Serial # of your tool.

Routine Preventative Maintenance:

• To extend motor life, remove debris from motor every 20 hrs. with compressed air into the air slots.

• Mineral spirits are recommended when cleaning. Do not use on electrical components or clean tool or parts with any solvents or oils containing acids, esters, ketones,

chlorinated hydrocarbons or nitro carbons. Compressed air may be used to remove dirt from electrical components.

• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

• Tool markings and labels must be kept legible at all times, if not, reorder and replace.

• Visually inspect plug and cord for frays, visible damage and signs of deterioration. Damaged or worn components must be replaced by Dynabrade or qualified repair

technician to avoid a safety hazard.

• Check brushes regularly for wear. Unplug tool, unscrew brush caps and ensure brush wear has not reached wear mark. Clean brushes before reassembling, make sure it

slides freely in holder.

• After maintenance is performed on tool check for excessive tool vibration.

• If the electrical components have been disturbed during repair, check for excessive current leakage at 550 volts with a current leakage checker on all screws

and the gear case.

Handling and Storage of Tool and Accessories:

• Use of tool rests, hangers and/or balancers is recommended.

• DO NOT carry tool by cord.

• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

Model

Motor

Number

RPM

51582

0 - 3,000

51583

0 - 3,000

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date of

purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or replace at

our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have been defective.

Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to

equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as

bearings, brushes, gears, etc., are not covered under this warranty.

Reference Contact Information

Government Printing Office – GPO

Superintendent of Documents

Attn. New Orders

P.O. Box 371954

Pittsburgh, PA 15250-7954

Tel: 1 (202) 512-1803

Visit Our Web Site: www.dynabrade.com

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

TOOL DESCRIPTION

ASSEMBLY and OPERATION INSTRUCTIONS

MAINTENANCE and ACCESSORY CARE INSTRUCTIONS

Machine Specifications

Max. Motor

hp (w)

Voltage

Current

1.8 (1342)

120 V (AC)

11 Amp

1.8 (1342)

120 V (AC)

11 Amp

One Year Warranty

Phase

Frequency

60 Hz

Email: [email protected]

PRINTED IN USA

Weight

Length

Pound (kg)

Inch (mm)

11.8 (5.35)

21 (533)

13.1 (5.94)

22 (559)

DYNABRADE

Height

Inch (mm)

7 (178)

PD09.30