ADEMCO ADEMCO VISTA-20PSIA Handleiding voor programmering - Pagina 2
Blader online of download pdf Handleiding voor programmering voor {categorie_naam} ADEMCO ADEMCO VISTA-20PSIA. ADEMCO ADEMCO VISTA-20PSIA 17 pagina's. Ademco vista series security system
Ook voor ADEMCO ADEMCO VISTA-20PSIA: Snelle installatiehandleiding (2 pagina's), Gebruikershandleiding (20 pagina's), Snelle installatiehandleiding (2 pagina's), Snelle installatiehandleiding (2 pagina's), Beknopte handleiding (2 pagina's)
Pagina afdrukken
TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control):
A. POWER UP, then press [ ✱ ] and [#] at the same time, within 50 seconds of powering up (this method must be used if ✱ 98
was used to exit program mode). OR
B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.
PROGRAMMING MODE COMMANDS
Task
Go to a Data Field
Entering Data
Review a Data Field
Deleting an Entry
Initialize Download ID
Reset Factory Defaults
Zone Programming
Function Key Programming Press ∗ ∗ ∗ ∗ 57. Unlabeled keypad keys (known as ABCD keys) for special functions
Zone Programming
(Expert Mode)
Output Device Mapping
Output Programming
Zone List Programming
Alpha Programming
Exit Program Mode with
installer code lockout
Exit Program Mode
SPECIAL MESSAGES
OC = OPEN CIRCUIT (no communication between Keypad and Control).
EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).
After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.
This will revert to a "Ready" message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this
delay by pressing [#] + [0].
If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after
you correct the programming.
TABLE OF DEVICE ADDRESSES
This Device
RF Receiver
AUI 1
AUI 2
Long Range Radio
4286 Voice Module
Zone Expanders (4219/4229):
module 1 (for zones 09 - 16)
module 2 (for zones 17 - 24)
module 3 (for zones 25 - 32)
module 4 zones 33 - 40
module 5 zones 41 - 48
Relay Modules (4204):
module 1
module 2
module 3
module 4
Keypads:
keypad 1
keypad 2
keypad 3
keypad 4
keypad 5
keypad 6
keypad 7
keypad 8
5800TM Module
** These module addresses apply to VISTA-20P only.
†† Addressable devices are identified by "1" plus the device address when reporting. Enter report code for zone 91 to enable addressable device
reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.
Command/Explanation
Press [∗ ∗ ∗ ∗ ] + [Field Number], followed by the required entry.
When the desired field number appears, simply make the required entry. When the last entry
for a field is entered, the keypad beeps three times and automatically displays the next data
field in sequence. If the number of digits that you need to enter in a data field is less than the
maximum digits available (for example, the phone number fields *41, *42), enter the desired
data, then press [∗ ] to end the entry. The next data field number is displayed.
Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
Press [∗ ∗ ∗ ∗ ] + [Field Number] + [∗ ∗ ∗ ∗ ]. (Applies only to fields ∗40 thru *46, *94, and pager fields)
Press ∗ ∗ ∗ ∗ 96. Initializes download ID and subscriber account number.
Press ∗ ∗ ∗ ∗ 97. Sets all data fields to original factory default values.
Press ∗ ∗ ∗ ∗ 56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800
RF transmitters.
Press ∗ ∗ ∗ ∗ 58. Same options as *56 mode, but with fewer prompts. Intended for those familiar
with this type of programming, otherwise *56 mode is recommended.
Press ∗ ∗ ∗ ∗ 79. Assign module addresses and map individual relays/powerline carrier devices
Press ∗ ∗ ∗ ∗ 80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers
Press ∗ ∗ ∗ ∗ 81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
Press ∗ ∗ ∗ ∗ 82. Zone alpha descriptors
Press ∗ ∗ ∗ ∗ 98. Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0.
To reenter programming mode, the system must be powered down, then powered up. Then
use method A above. See field *88 for other *98 Program mode lockout options.
Press ∗ ∗ ∗ ∗ 99. Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or
method A above.
Uses Address Reports as ††
00
100
01
101
02
102
03
103
04
104
07
107
08
108
09**
109
10**
110
11**
111
12
112
13
113
14**
114
15**
115
16
n/a
17
n/a
18
n/a
19
n/a
20
n/a
21
n/a
22
n/a
23
n/a
28
n/a
Enabled By...
*56 zone programming: input device type entry
Automatic if AUI enable field *189 enabled for AUI 1
Automatic if AUI enable field *189 enabled for AUI 2
automatic if output to long range radio field *29 enabled
automatic if phone module access code field *28 enabled
*56 zone programming: input device type entry, then:
automatic if zone no. 9-16 entered as AW type or relay assigned
automatic if zone no. 17-24 entered as AW type or relay assigned
automatic if zone no. 25-32 entered as AW type or relay assigned
automatic if zone no. 33-40 entered as AW type or relay assigned
automatic if zone no. 41-48 entered as AW type or relay assigned
*79 output device programming: device address prompt:
entered at device address prompt
entered at device address prompt
entered at device address prompt
entered at device address prompt
data field programming as listed below:
always enabled, all sounds enabled.
data field *190
data field *191
data field *192
data field *193
data field *194
data field *195
data field *196
automatic
– 2 –