Ganz Lite LDB series Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Ganz Lite LDB series. Ganz Lite LDB series 2 pagina's. 600 tvl day / night color camera

Pagina afdrukken
Precautions
Do not attempt to dismantle the camera module mounted
within the dome. There are no user serviceable parts within the
camera module. Refer servicing to qualified personnel.
Handle the camera with care. Do not abuse the camera.
Avoid striking or shaking it. Improper handling and storage
could damage the camera.
Do not operate the camera beyond its temperature,
humidity or power source rating. Please refer to the
environmental information provided overleaf.
Emissions
FCC COMPLIANCE: This equipment complies with Part 15 of
the FCC rules for intentional radiators and Class B digital devices
when installed and used in accordance with the instruction manual.
Following these rules provides reasonable protection against harmful
interference from equipment operated in a commercial area.
This equipment should not be installed in a residential area as
it can radiate radio frequency energy that could interfere with
radio communications, a situation the user would have to fix at their
own expense.
Install Methods
A. By using the base mounting holes
B. By using the quick install adaptor
Template
Surface mount (In a wall or ceiling)
Using Quick Install Adaptor:
Create an aperture in the mounting surface to a diameter of
Side Knock-out
1.5" (38mm) as indicated by "T2".
The aperture is also avaliable for cable access (3/4", 19mm).
Using screws:
Create four holes at template positions 'T1', use the screws
and plugs provided in the screw kit where the mounting
surface is appropriate.
When the cables are threaded through the mounting surface,
create an apture indicated "T2". It can be simply threaded for
use with the quick install adapter .
When mounting the dome on a surfce with the four T1 screws,
use one of the side knock-outs as indicated for cable entry
(see Installation Guide overleaf ).
Side Knock-out
T1
1
T1
T2
T1
T1
2
Dome Base
PAN 360°
3
TILT 90°
Camera Module
ROTATE 360°
4
Camera Liner
5
Dome Cover
Side Knock-out
T1
T2
T1
Cable Access
T1
T1
Side Knock-out
1.
Preparation before installation
Use the template (see overleaf) to mark-out and prepare the mounting area.In
order to mount the base, first remove the camera module by gently pulling down
on the tabs that hold the camera module in place (see image right) and remove
camera assembly. To re-assemble gently pull down on the tabs and insert the
camera assembly.
A
Mounting Surface
Using the base mounting holes:
A.
3/4"
Side
When mounting the dome to a ceiling or wall using screws, first knock out the screw
Knock-outs
Rubber Grommet
access holes that correspond to the template marks "T1".This can be done by using a
cross-point screwdriver.
Cable Notch
Cable Notch
Push the cables through the dome base and 3/4" rubber grommet.
Install the grommet on the base to prevent dust ingress. Cables may be routed through
the mounting surface if an appropriate hole is made at location T2.
Mount with the Dome Base
If using the side knock-out, make sure the video-power cables are properly arranged in
the cable notch and exit out of the side knock without being crushed (see image A).
B
Video-Power Cables
Using the Quick Install Adaptor(Optional):
B.
When mounting the dome to a ceiling using the quick install adaptor, use
1/2"Rubber Grommet
the template to cut a hole as the circle marked "T2" with a hole cutter.
Install the adaptor into the mounting surface and use the screws to adjust
the position of the two locking arms on the quick install adaptor to adjust
Mounting Surface
to the mounting surface.
Push the cables through the opening and 1/2"
rubber grommet. Make sure the grommet is
properly installed on the adaptor to prevent
dust ingress (see image B).
Mount with the Quick Install Adaptor
C.
Mount on a US Single Gang Box:
C
3/4"
Rubber Grommet
When mounting the dome to the box, carefully remove the screws on the box.Install the 3/4"
T1
grommet on the base to prevent dust ingress, then push the cables through the dome base
and 3/4" rubber grommet.
Mount the dome base on the box and reinstall the two screrws.
Tighten the screws sufficiently on the box (position T1, see image C).
T1
Removing the dome cover and the camera liner
Gently turn the dome cover counter-clockwise to unlock and pull free of the dome base.
Dome Base
Remove the camera liner by gently pulling it free of the 4 notches in the camera base (see
US Single Gang Box
image A).
Opening the required knock-out panel
Open one of the side knock-outs (see image A) to the size required to allow cable entry.
Mount on a pre-installed US Single Gang Box
2.
Mount the dome enclosure
By using the base mounting holes, the dome base can be fixed on the wall or
ceiling with attached screws.
Note: When using Quick Install Adaptor, re-assemble the parts of dome, then
mount the whole dome onto adaptor (see image B).
3.
Install camera module
Push the video-power cables through the opening
Feed the pre-connected video-power cables through the appropriate point. Then push the
cable out of the opening. Make sure the cable is positioned on the proper location and
out of the side knock-out, if required.
Gimble
Adjust the camera position
Screw
To adjust the tilt angle, first loosen the 2 screws
on the gimble (See image right) make your
adjustments then retighten the screws.
The focus and range of the lens can be adjusted
(depending on the lens, see instructions
Gimble
overleaf).
Note: Do not attempt to adjust the camera position by holding the lens as this will cause
damage to the camera.
Make adjustments by tilting and rotating the gimble assembly.
PULL
Loosen the tab and pull out the camera assembly
Quick Install Adaptor
Locking Arms
Install Quick Install Adaptor on indoor ceiling
4.
Install the camera liner
Carefully fit the camera liner over the camera base so
that it snaps into place (as shown in image 4), and do
not obstruct the camera lens.
Install the Dome Liner on
the Camera Module
5.
Replace the dome cover
Replace the dome cover and rotate clockwise to close it (as shown in image 5).
6.
Tighten the tamper-proof screw
Use the supplied torx driver and the tamper-
Tamper-proof Screw
proof screw (T2x5L) to secure the dome
cover.
Tighten tamper-proof
screw