CORNING MicroDEN Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} CORNING MicroDEN. CORNING MicroDEN 10 pagina's.

Pagina afdrukken

4. Setting up the Corning® MicroDEN® Unit

The Corning MicroDEN unit requires working within a biosafety cabinet to

maintain sterility. The following protocol is for seeding enriched monocytes

(MOs).

Overview

The differentiation of MOs to dendritic cells is a multi-day process that involves

seeding enriched MOs into 2 single-use flasks followed by a medium refresh

on Day 3 and dendritic cell harvest on Day 6. Duration may be increased or

decreased depending on preference. Perfusion volume requirements should be

adjusted accordingly.

The set-up process involves transferring the unit and consumables between the

biosafety cabinet and incubator. Care should be taken to ensure the unit and

consumables are handled properly (avoid aggressive motions such as dropping

and/or hitting against a wall) to prevent disturbing the cultured cells.

The cell culture flasks may be seeded with either enriched MOs or with

peripheral blood mononuclear cells (PBMCs) where the MOs are enriched

through plastic adherence. The following protocol is based on seeding enriched

MOs, but the process can be amended for seeding PBMCs and enriching MOs

through plastic adherence.

A base medium compatible with dendritic cell generation should be used,

although this is not a requirement for proper function of the unit and

consumable. Differentiation medium consists of base medium plus the

cytokines IL-4 and GM-CSF to facilitate differentiation of MOs into immature

dendritic cells (iDCs). Generated iDCs can subsequently be matured in the same

flasks, if desired. Each flask has a volume of 13.2 mL and a cell culture area of

39.7 cm

. 80 mL of differentiation medium is added to the inlet bottle on set-up

(Day 0) and Day 3. The recommended cytokine concentration of differentiation

medium is 350 U/mL, although this can be changed based on user preference.

The Corning MicroDEN unit has four pre-programmed flow rates:

1. Seeding (6.50 mL/min.)

2. Prime (6.50 mL/min.)

3. Culture (8.0 µL/min.)

4. Harvest (13.50 mL/min.)

The following protocol assumes a 6-day differentiation, thus inlet bottle

volumes are given for 3-day intervals. For example, 3 days of perfusion at 8.0

µL/min./flask will require 80 mL of differentiation medium (70 mL for perfusion

plus 10 mL excess). Users should optimize the process for their particular

cell type and objectives. The volume of differentiation medium added to the

inlet bottle should be adjusted based on duration of run and media refresh

requirements. During culture, medium flows from the inlet bottle, through the

flasks, and into the outlet bottle. The outlet bottle does not need to be emptied

for a 6-day run, but the outlet bottle should be emptied if the run duration is

longer than 6 days.

Unit and Flask Set-up

Lightly spray the Corning® MicroDEN® unit and consumable set with 70%

ethanol and place inside the biosafety cabinet. Remove the flasks and

thermoform from the packaging and place the tray on the unit. Flasks and

components are pre-assembled. Inspect that all connections are tight and

secure. Inspect for any creased tubing that may inhibit flow.

5. Cell Seeding

Cells can be seeded into the Corning MicroDEN flasks by either (Method 1)

positive pressure using a pipettor or (Method 2) pump perfusion.

1. Suspend enriched MOs in 25.0 mL of differentiation medium.

2. Remove the seeding bottle from the tray.

3. Open the bottle.

To unscrew the cap, turn the bottle while keeping the cap and tubing set in

◗ –

place so the tubes don't twist. Take care not to touch the dip tubes to any

non-sterile surface (Figure 1).

4. Pipet cell solution into the seeding bottle.

5. Insert tubing set and cap back onto the bottle. While pressing down on the

tubing set, rotate the orange cap to tighten the assembly to the bottle

(Figure 1). Place the bottle back into the thermoform tray.

Hold cap and rotate the

bottle to remove the cap

assembly.

Figure 1. Cap assembly.

Gently press down on the

white tubing set and rotate

the orange cap to assemble.