KitchenAid KESC300BBL1 Handleiding voor installatie-instructies - Pagina 3

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} KitchenAid KESC300BBL1. KitchenAid KESC300BBL1 7 pagina's. 30" (76.2 cm) electric slide-in range with self-cleaning thermal/convection oven
Ook voor KitchenAid KESC300BBL1: Gebruiks- en onderhoudshandleiding (5 pagina's)

Pagina afdrukken

Tools needed for

installation:

level

flat-blade screwdriver

or 5/16" (0,8 cm) nut

driver

Power supply cord

Use a new 40-amp

power supply

cord.

Local codes may permit the use of a U.L.-listed,

250-volt, 40-ampere range power supply cord

(pigtail). Power supply cord should be Type SRD

or SRDT and be at least four feet long. The wires

that connect to the range must end with ring

terminals. A 3/4" (1.9 cm), U.L.-listed strain relief

must be installed where the power supply cord

connects to the range. (See Figures 1 and 2.)

Electrical

connections

NOTE: The metal chassis of the range MUST be

earth-grounded in order for the control panel to work,

If the metal chassis of the range is not earth-

grounded, NO keypads will operate. Check with a

qualified electrician if you are in doubt as to whether

the metal chassis of range is earth-grounded.

318" (0.95 ¢m)

Phillips

ratchet

screwdriver

wrench

hand or electric drill wood

floor: 1/8" (0,3 cm) drill bit

concrete/ceramic

floor:

3/16" (0.48 cm) carbide-

tipped masonry drill bit

measuring tape

Parts supplied for

installation:

anti-tip bracket

2 plastic anchors

(#10 x 1-1/2")

(Bracket

must be securely mounted to sub-

floor, Thickness

of flooring may require longer

screws to anchor the bracket to sub-floor,)

Electrical

requirements

Save Installation Instructions for the local

electrical inspector's use.

Power supply cord is not provided and is

available through your local electrical

supply houses.

Electrical Shock Hazard

• Electrical ground is required on this

appliance,

• Use only a new power supply cord kit rated

at 250 volts, 40 amperes and investigated

for use with ranges. Do Not reuse an old

power supply cord.

• Do Not modify the power supply cord plug.

If it does not fit the outlet, have a proper

outlet installed by a qualified electrician.

• Do Not use an extension cord with this

appliance.

• Do Not ground to a gas pipe.

• Do Not have a fuse in the neutral or

grounding circuit. A fuse in the neutral or

grounding circuit could result in an

electrical shock.

• Check with a qualified electrician if you are

in doubt as to whether the appliance is

properly grounded,

Failure to follow these instructions could

result in serious injury or death.

If codes permit and a separate grounding wire

is used, it is recommended

that a qualified

electrician determine that the grounding path

is adequate.

A three-wire or four-wire, single-phase, 120/240-

volt, 60-Hz, AC-onty, electrical supply (or three-

wire or four-wire 120/208-volt if specified on the

serial/rating plate) is required on a separate

40-ampere circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended.

THE RANGE MUST BE CONNECTED WITH

COPPER WIRE ONLY.

Wire sizes (COPPER WIRE ONLY) and

connections must conform with the rating of the

appliance (40 amperes).

A wiring diagram is located on back of range.

Panel B

ring

terminals

NEUTRAL

This blade connected

_to

thi_

3,,(,;;

.=,/,.=.T

U.L-listed

NEUTRAL

strain relief

(white or center)

Three-wire

power supply

cord

NEMA

10-50P

Figure

3/4" (1.9 cm)

U.L.4isted

NEUTRAL

strain _e)

Four-wire

power supply

cord

(Mobile

home or other four-wire

installations)

NEMA 10-50P

Figure 2

The power supply cord must have three No.-lO

copper wires to match a three-wire receptacle of

NEMA Type 10-50R. (See Figure 3.)

For mobile home or other four-wire installations:

This appliance is manufactured with ground

connected to cabinet. The ground must be

revised so the green grounding wire of the four-

wire power cord is connected to the cabinet. See

four-wire electrical connection section, Panels C

and D.

When a four-wire receptacle of NEMA Type

14-50R is used (See Figure 4.), a matching

U.L.-listed, four-wire, 250-volt, 40-ampere, range

power supply cord (pigtail) must be used. This

cord contains four copper conductors with ring

terminals on the appliance end, terminating in a

NEMA Type 14-50P plug on the supply end. The

fourth (grounding) conductor must be identified

by a green or green/yellow cover and the neutral

conductor by a white cover. Cord should be Type

SRD or SRDT with a U.L.-listed strain relief and

be at least four feet long.

The MINIMUM conductor sizes for the copper

4-wire power supply cord are:

40-ampere circuit

2, No.-8 conductors

1, No.-10 white neutral

1, No.-8 green grounding

For use where

local codes

_lermit use of

exible power

supply cord.

three-wire

wall

receptade

(10-50R)

Figure 3

four-wire wall

receptacle

(14-S0R)

Figure 4

Direct wire

The range can be connected directly to fused

disconnect or circuit breaker box through flexible,

armored or non-metallic sheathed, copper cable

(with grounding wire). Do Not use two-wire with

bare grounding wire. All current-carrying

wires

must be insulated.

A U.L-listed conduit connector must be provided

at each end of the power supply cord (at the

appliance and at the junction box). USE ONLY

10-GAUGE SOLID COPPER WIRE. DO NOT

USE ALUMINUM. Allow two or three feet of slack

in the line so the range can be moved if servicing

is ever necessary.

Where local codes permit connecting

the

frame-grounding

conductor to the neutral

(white) junction box wire:

This appliance is manufactured

with the

neutral terminal connected to the cabinet. If

local codes Do Not permit connecting

cabinet-grounding

conductor to neutral wire,

use "Four-wire

connection" instructions.

Electrical Shock/Fire Hazard

Check that wiring you are using matches

colors shown in illustrations and specified

in instruction steps. If wiring does Not

match, it is your responsibility

to have a

qualified electrician install correct wiring.

Failure to follow these instructions could

result in fire, electrical shock or death.

Turn power supply off.

I _

terminal

block

Figure 5

cover

2 • Remove the terminal block cover located on

back of range. Remove the 3/8" (0.95 cm) brass

terminal nuts attached to the knockout.

Remove

knockout

openingfor

40-am pare _

power

supply cord

Figure 6

Remove the knockout for the 40-ampere

power supply cord.

silver-colored

_rounding

40-ampere

(white)

wire

, U.L,-listed

strain relief

Figure

Attach a 3/4" (1.9 cm) U.L.-listed strain

relief (U.L. marking on strain relief) to the

opening. Tighten strain relief firmly to cabinet.

Place power supply cord through strain relief.

Using the 3/8" (0.95 cm) brass nuts,

attach the neutral (white) wire of power supply

cord to the center, silver-colored screw of the

terminal block.

Connect the other two wires to the outer

terminal block screws. (See Figure 7.)

Do Not loosen the factory-installed

nuts on

the terminal block.

Be sure the wiring nuts are installed tight.

Tighten strain relief screws.

Reattach terminal block cover.