Gardena 7000/C Gebruikershandleiding - Pagina 5

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Gardena 7000/C. Gardena 7000/C 13 pagina's. Clear water submersible pump / dirty water submersible pump

Pagina afdrukken

To connect the hose [ Fig. I4 ]:

(1)

(2)

1. Put the connection

outlet of the pump.

3. OPERATION

The pump can be operated in both automatic and manual

modes.

Automatic operation [ Fig. O1 ]:

(5)

The float switch

turns the pump on automatically when

the water level exceeds the cut-in height and the water is

pumped out. The float switch

as soon as the water level falls below the cut-out height.

1. Stand the pump on a firm surface

– or –

use a rope attached through the bore hole

carrying handle to immerse the pump in a well or

shaft. During automatic operation, ensure that the float

(5)

switch

can move freely.

2. Connect the power cable into a mains socket.

To adjust the cut-in and cut-out height [ Fig. O2 ]:

The cut-in height and cut-out height (see 7. TECHNICAL

DATA) can be adjusted.

v Press the cable of the float switch

(7)

the float switch lock

• To ensure the pump is switched off safely, always fix the

cable of the float switch in place in one of the three float

switch locks on the pump handle.

4. MAINTENANCE

DANGER! Electric shock!

Risk of injury due to electric shock.

v Disconnect the product from the mains before

you do maintenance.

The GARDENA Clear Water Submersible Pump / Dirty

Water Submersible Pump should not require regular main-

tenance.

To flush the pump:

After pumping pumped chlorinated swimming pool water

or other liquids leaving residues, the pump should be

flushed with clear water.

1. Immerse the pump in clear water.

2. Flush the pump with clear water.

5. STORAGE

To put into storage:

v The product must be stored away from children.

v Clean and stowe the product in a frost-free place before

the first frost arrives.

(3)

(4)

with the collar

on the

(5)

turns the pump off again

(6)

in the

(5)

into an opening in

2. Tighten the collar

(4)

3. Connect the hose with the connection.

• Do not select a cable length that is too long or short to

ensure that the float switch can turn on and off properly.

• The higher the opening of the float switch lock

higher the cut-in and cut-out height.

• The shorter the length of cable between the float

(5)

switch

and the float switch lock

cut-in height and the higher the cut-out height.

• The cable length between the float switch

(7)

float switch lock

must always be at least 10 cm.

Manual operation [ Fig. O3 ]:

The minimum residual water depth (see 7. TECHNICAL

DATA) is only achieved in manual mode because the float

switch already switches off the pump before this when in

automatic mode.

(5)

1. Push the float switch

with the cable downward.

2. Stand the pump on a firm surface

– or –

use a rope attached through the bore hole

carrying handle to immerse the pump in a well or shaft.

3. Connect the power cable into a mains socket.

The pump remains in constant operation because the float

switch is bypassed.

To clean the suction base and the feed impeller

[ Fig. M1 / M2]:

1. Unlock (counterclockwise) the 5 turn-locks

a screwdriver.

2. Remove the suction base

(11)

3. Loosen the nut

4. Remove the feed impeller

5. Clean the suction base

(9)

(12)

6. Put the washer

and the feed impeller

shaft.

(11)

7. Screw the nut

on the motor shaft.

(9)

8. Put the suction base

9. Lock (clockwise) the turn-locks

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal

household waste. It must be disposed of in line with

local environmental regulations.

(7)

, the

(7)

, the lower the

(5)

and the

(7)

onto the float switch lock

(6)

in the

(8)

with

(9)

(10)

(12)

and the washer

and the feed impeller

(10)

on the motor

on the pump.

(8)

with a screwdriver.