Indesit I6GG1FX/I Gebruiksaanwijzing - Pagina 19
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Indesit I6GG1FX/I. Indesit I6GG1FX/I 48 pagina's.
! If one or more of these conditions is not fulfilled or if
the cooker must be installed according to the conditions
listed for class 2 - subclass 1 appliances (installed
between two cupboards), the flexible steel hose must
be used instead (see below).
Connecting a flexible jointless stainless steel pipe to
a threaded attachment
Make sure that the hose and gaskets comply with current
national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres, making
sure that the hose is not compressed and does not come
into contact with moving parts.
Checking the tightness of the connection
When the installation process is complete, check the hose
fittings for leaks using a soapy solution. Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas other
than the default type (this is indicated on the rating label
on the cover).
Adapting the hob
Replacing the nozzles for the hob
burners:
1. Remove the hob grids and
slide the burners off their seats.
2. Unscrew the nozzles using a 7
mm socket spanner (see fi gure),
and replace them with nozzles
suited to the new type of gas (see
Burner and nozzle specifications
table).
3. Replace all the components by following the above
instructions in reverse.
Adjusting the hob burners' minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory screw,
which is positioned inside or next to the tap pin, until the
flame is small but steady.
! If the appliance is connected to a liquid gas supply, the
regulatory screw must be fastened as tightly as possible.
3. While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
! The hob burners do not require primary air adjustment.
Adapting the oven
Replacing the oven burner nozzle:
1. Open the oven door fully
2. Pull out the sliding oven bottom (see diagram).
3. Remove the oven burner after unscrewing the screws
V (see fi gure).
4. Unscrew the nozzle using a special nozzle socket
spanner (see fi gure) or with a 7 mm socket spanner, and
replace it with a new nozzle that is suited to the new type
of gas (see Burner and nozzle specifi cations table).
Adjusting the gas oven burner's minimum setting
1. Light the burner (see Start-up
and Use).
2. Turn the knob to the minimum
position (MIN) after it has been in
the maximum position (MAX) for
approximately 10 minutes.
3. Remove the knob.
4 . T i g h t e n o r l o o s e n t h e
adjustment screws on the outside
of the thermostat pin (see fi gure)
until the flame is small but steady.
! If the appliance is connected to
liquid gas, the regulation screw
V
must be fastened as tightly as
possible.
5. Turn the knob from the MAX
position to the MIN position
quickly or open and shut the oven
door, making sure that the burner
is not extinguished.
! Be careful of the spark plug
wires and the thermocouple
tubes.
! After adjusting the appliance so it may be used with a
different type of gas, replace the old rating label with a
new one that corresponds to the new type of gas (these
labels are available from Authorised Technical Assistance
Centres).
GB
19