Indesit I6GG1FX/I Manual de Instruções - Página 19

Procurar online ou descarregar pdf Manual de Instruções para Fogões Indesit I6GG1FX/I. Indesit I6GG1FX/I 48 páginas.

Imprimir página

! If one or more of these conditions is not fulfilled or if

the cooker must be installed according to the conditions

listed for class 2 - subclass 1 appliances (installed

between two cupboards), the flexible steel hose must

be used instead (see below).

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres, making

sure that the hose is not compressed and does not come

into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the hose

fittings for leaks using a soapy solution. Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

Adapting the hob

Replacing the nozzles for the hob

burners:

1. Remove the hob grids and

slide the burners off their seats.

2. Unscrew the nozzles using a 7

mm socket spanner (see fi gure),

and replace them with nozzles

suited to the new type of gas (see

Burner and nozzle specifications

table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners' minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until the

flame is small but steady.

! If the appliance is connected to a liquid gas supply, the

regulatory screw must be fastened as tightly as possible.

3. While the burner is alight, quickly change the position of the

knob from minimum to maximum and vice versa several times,

checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

Adapting the oven

Replacing the oven burner nozzle:

1. Open the oven door fully

2. Pull out the sliding oven bottom (see diagram).

3. Remove the oven burner after unscrewing the screws

V (see fi gure).

4. Unscrew the nozzle using a special nozzle socket

spanner (see fi gure) or with a 7 mm socket spanner, and

replace it with a new nozzle that is suited to the new type

of gas (see Burner and nozzle specifi cations table).

Adjusting the gas oven burner's minimum setting

1. Light the burner (see Start-up

and Use).

2. Turn the knob to the minimum

position (MIN) after it has been in

the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4 . T i g h t e n o r l o o s e n t h e

adjustment screws on the outside

of the thermostat pin (see fi gure)

until the flame is small but steady.

! If the appliance is connected to

liquid gas, the regulation screw

must be fastened as tightly as

possible.

5. Turn the knob from the MAX

position to the MIN position

quickly or open and shut the oven

door, making sure that the burner

is not extinguished.

! Be careful of the spark plug

wires and the thermocouple

tubes.

! After adjusting the appliance so it may be used with a

different type of gas, replace the old rating label with a

new one that corresponds to the new type of gas (these

labels are available from Authorised Technical Assistance

Centres).