DEZIT DZ 024 EIS W Handmatig - Pagina 5

Blader online of download pdf Handmatig voor {categorie_naam} DEZIT DZ 024 EIS W. DEZIT DZ 024 EIS W 16 pagina's. Electric panel heater

Pagina afdrukken

and

buttons, provided that the appliance is in programming mode.

Note: When you turn on the appliance, it will start operating in the (heating

or programming) mode which it has last operated.

Note: You can switch between the modes of operation (heating or

programming) by shortly pressing the "Timer" button when the

appliance is switched on.

"Return to factory settings" function

When the convector is in "Off" mode, press the

simultaneously for six seconds; then the display will show „_ _ __" and rotating

symbols. When it is "reset", the display will show the measured value of the

room temperature.

After using the reset function, you need to re-enter the settings of the

following functions:

•

time setting

•

enter a value of the temperature correction (if needed)

•

disable the "Anti-frost" function (if needed)

•

disable the "Adaptive start" (if needed)

•

weekly programme - 24/7

If the electric convector is disconnected from the mains, this will not affect

the set temperature and the mode of operation which has been active prior

to its disconnection. If for example the convector has been in "Heating" mode,

after it has been disconnected and reconnected to the mains, it will continue

operating in the same mode with the same set temperature.

The principle of operation of the electric convector with energy-

independent memory is to store the settings for 90 minutes

guaranteed, and up to 150 minutes not guaranteed.

When the room temperature is lower than the temperature set by the

electronic thermoregulator, the convector will start operating and will

continue operating until the room temperature reaches the set value. When

the room temperature is higher than the temperature set by the electronic

thermoregulator, the convector will automatically go into "Standby" mode.

Information presented on panel heater display

Indications when you are not in settings mode:

a. In Off mode – consecutively showing:

•

time (hour and minutes)

•

measured room temperature

b. In Heating mode – it shows the measured room temperature

c. In Programming mode – consecutively showing:

•

Day of the week, low line and the measured temperature. 6_22

•

Day of the week, low line and the temperature set in the programme

blinking (set for the current hour), which may be also the OFF symbol. 6_23

d. Upon connecting the convector to power supply the display shows:

•

Hyphens "----", if the appliance has been in Off mode before disconnecting

it from the power supply.

•

Hyphens "----", which in 2 seconds will be replaced by the value of the

current temperature, if the appliance has been in On mode before

disconnecting it from the power supply.

e. Two numerals (01÷96) and a blinking yellow LED indicate the remaining time

in hours until the delayed start, if the appliance has been in "Delayed start"

mode before disconnecting it from the power supply.

With the purpose of further energy saving, the electronic thermoregulator

reduces the brightness of illumination of all LEDs. Upon pressing any of the

buttons the brightness increases for 8 seconds and it is then reduced again.

g. If the display shows "t1" or "t2", this means that the self-diagnostic system has

found a problem with the temperature sensor. "t1" indicates a disconnected

cable at the sensor, while "t2" indicates short circuit at the sensor. In this case

the electric convector will be automatically switched off and it can be switched

on again only after the problem has been fixed. The problem has to be handled

by a qualified specialist.

h. Upon switching on the power supply the display will show hyphens "----" for 2

seconds instead of temperature of time.

When the digital display shows the temperature the "Temperature" LED is lit,

and when it shows the time, the "Timer" LED is lit.

PROTECTION

•

The appliance is equipped with a safety thermo turn-off device, which

English

•

CLEANING

•

and

buttons

•

STORAGE

•

MAINTENANCE OPERATIONS OF THE APPLIANCE

•

DIMENSIONS OF HEATED VOLUME AND HEATED AREA OF A ROOM /

APPLIANCE MODELS

Model

DZ 024 050 EIS W - 500W

DZ 024 100 EIS W - 1000W

DZ 024 150 EIS W - 1500W

DZ 024 200 EIS W - 2000W

DZ 024 250 EIS W - 2500W

* Minimum guaranteed heated volume (area) for heating at an average capacity of heat transmission

factor λ=0.5 W/(m

average value of λ=0.35 W/ (m

automatically turns the heater off in cases of extreme temperature of the

panel heater /i.e. overheating of the appliance/.

The safety thermo turn-off device will automatically restore the heater

operation when the temperature of the appliance falls below the

permissible ultimate values.

It is compulsory first to turn off the appliance through its power

switch and to disconnect it from the power socket. Before starting the

cleaning session you should wait until the panel heater cools down in a

disconnected state.

Clean the heater body with damp cloth, vacuum cleaner or a brush.

Never immerse the appliance into water – there is danger for your life from

electric shock!

Never use gasoline, thinner or hard abrasive products to clean the

appliance, because they will damage the appliance coating.

Before putting the panel heater away let it cool down after you have

disconnected it from the power socket

Use the appliance original packing to store it, if the panel heater will not

be in use for a long period of time. By storing the product in its original

packing you protect it from excessive dirt and dust accumulation.

Never put a hot panel heater in its packing!

It is necessary the product to be stored at a dry and dark place, protected

from direct sun light.

It is explicitly forbidden to store the panel heater in damp and wet premises.

In case of appliance malfunction, please contact the authorized service

center closest to your location. /service centers are indicated in appliance

warranty documents/.

Important: In case of a claim and/or violation of your consumer rights,

please contact the supplier of this appliance at the indicated locations or

via the Internet page of the company: www.tesy.com

Heated volume

10* - 15 m

20* - 30 m

30* - 45 m

40* - 60 m

50* - 70 m

K) for a heated room. Higher values of heated volume (area) can be achieved at an

K). Standard height of heated rooms – 2.5 meters.

Heated area

4* - 6 m

8* - 12 m

12* - 18 m

16* - 24 m

20* - 28 m

Operation and Storage Manual of Panel Heater