AVYCON AVR-HN504P4 Snelstarthandleiding

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} AVYCON AVR-HN504P4. AVYCON AVR-HN504P4 2 pagina's.

Pagina afdrukken

Network Video Recorder

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.

All the examples and pictures used here are for reference only. There may be several technically incorrect places

or printing errors in this manual. The updates will be added into the new version of this manual. The contents of

this manual are subject to change without notice.This device should be operated only from the type of power

source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

1. Packing Check

Please check the device and the accessories after getting the device.

If there are any damages, shortages or defects, please contact your

dealer immediately.

2. HDD Installation

This series of the product supports 8 SATA hard drives.

The pictures of the installation are only for reference, please take the

real object as standard. Please make sure that the device is powered off

before installation

1. Remove the cover and loosen the screws to take out two mounting bars.

2. Get ready the HDDs installed and ﬁx the HDDs on the mournting bar.

(For installing the HDDs well, please ﬁx the round screw holes ﬁrst)

3. Install the mounting bar with HDDs back to the device.

4. Connect the power and data cables.

5. Install the upper four HDDs as the method mentioned above and

install back cover

3. Rear Panel Installation

ALARM OUT

RS 485

P/Z

VGA

LAN 1

LAN 2

HDMI 2

USB3.0

USB

HDMI 1

K/B

Internet

The interfaces of the rear panel are for reference only.

4. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to "Main Menu" and then select "Shutdown" icon. This will bring

up a shutdown window. The device will shut down by clicking "OK"

button. Then disconnect the power.

4. Login

For our HN500 series NVRs, the default username is admin and the

default password is 123456. When starting HN500 series NVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can

skip this wizard if you would like, but it will help you conﬁgure basic

settings for your NVR. The wizard may allow you to also change the

default password for better security. If you decide to skip the wizard,

to access the live view and start using your NVR click on the Start

button in the bottom left of the menu bar on the bottom of the

screen and then click on Login and enter in the default password.

Username

admin

Password

Enter Password

Display Password

Edit Security Question

Network Configuration

After you ﬁnish adding IP cameras, you can see the live images through

the monitor of the NVR. The following will mainly introduce how to add

the IP cameras via LAN/WAN. This NVR has two network ports, you can

select the network work pattern as required. Network fault tolerance

and multiple address setting are optional.

Network Fault Tolerance: Bound two network ports to one IP address.

This pattern can increase the network bandwidth and form a network

redundant array to share the load. When one port goes wrong, the

otehr port will take over the entire load immediately and seamlessly.

Multiple Address Setting: You shall set the IP address, subnet mask,

e-SATA 1

e-SATA 2

gateway and DNS of each ethernet port respectively.

ALARM IN

AUDIO

OUT

The pictures are only for referenc, please refer to User anua for details

• LAN

1. Set the network of the NVR. Go to Start → Settings →

AUDIO

Network → TCP/IP. Input IP address, subnet mask, gateway,

etc. If using DHCP, please enable DHCP in both the NVR and

the router.

2. Go to Start → Settings → Network → Port. Input HTTP port

(the default value is 80), server port (the default port is 6036).

3. Click "Apply" to save the settings.

IP Address Settings

Work Pattern

Obtain an IPv4 address automatically

Address

Subnet Mask

Gateway

Primary Card

Ethernet Port 1 ( Online )

MCA Address

MTU

Obtain DNS automatically

Preferred DNS

4. Go to Start → Settings → Camera → Add Camera. The NVR

will automatically refresh the cameras searched. The IPC which

supports the Onvif protocol may be added manually. If the IPC

searched is not in the same local network as the NVR, you

should select the device and click

Quickly Add

No.

Selected: 1/3

Remain Bandwidth: 108 / 120 Mb

Cancel

Network Fault Tolerance

(Modifying work pattern need to reboot )Gateway

Obtain an IPv6 address automatically

192 . 168 .

1 .

Address

0 .

Mask Length

192 . 168 .

1 .

Gateway

Ethernet Port 1

Ethernet Port 2 ( Online )

10 . 151 . 151 .

MAC Address

1500

to modify the IP address.

Add Camera

Manually Add

Add Recorder

Port

Edit

Subnet Mask

Protocol

Model

Address

192.168.1.20

255.255.255.0

XXX

192.168.1.38

255.255.255.0

XXX

192.168.2.45

255 255 255 0

XXX

4.0.0.1.beta1

Default Password

Add

Edit Camera

CE :98 :23 :75 :35 :22

Mac Address

Address

192 .168 . 1 . 45

Sync to IPC

Subnet Mask

255 . 255 . 255 . 0

Gateway

192 .168 . 1 . 1

Username

admin

Password

Cancel

Version

3.4.2

Cancel