Accusplit Eagle AE190XLM Gebruiksaanwijzing - Pagina 4

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Accusplit Eagle AE190XLM. Accusplit Eagle AE190XLM 5 pagina's. Accusplit pedometer instruction manual

Pagina afdrukken

RESETTING YOUR PEDOMETER

Resetting TRIP Memories

Most people prefer to reset counts daily. T o reset your regular

counts (Trip Memories): From STEP , T IME, DISTANCE, or

CALORIE mode, press and hold the yellow RESET button for

at least 2 seconds. Y ou'll see the values all go back to zero.

The T OTAL memories stay as they are when resetting the T RIP

memories.

Resetting TOTAL and TRIP Memories

To reset your T OTAL Memories (which always resets T RIP

Memories) , go into T otal Memory Recall Mode. Press and

hold the yellow RESET button for at least 2 seconds to clear

BOTH TOTAL and TRIP memories.

CHANGING STEP FILTER SETTING

While the JW200 PedometerEngine™ Step Sensor is

extremely accurate, some people like to have the ability to

filter out false steps. T herefore, the unit has a variable setting

step filter, to allow fine-tuning to your specific preferences.

You can set the value to any value from 0 – 5 steps. For

example, if the filter is set to "3" , the unit will wait to start

counting steps until more than three steps have been taken in

less than five seconds.

Press S3+ (MODE) or S3– (RESET) to change the Step Filter

Setting.

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units (in, mi, and lb - this

is the default), or in Metric units (cm, km, and kg). From within Deep

Set mode (see pg. 25), press the S2 (MEMORY) button to cycle back

and forth between setting the Step Filter set point and Choice of Unit

System. T he unit will show either "US" or "EU" (for European Union)

depending on the unit system chosen. If you change units after using

the pedometer, the unit will convert all of your data into the new unit

system when you exit Deep Set model. Y ou can check to see which

system of units you are using by seeing which measurement units

are displayed on the Stride and Weight setting screens.

Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.

Press and hold S4 (MEMORY) for 2 seconds to exit Deep Set Mode.

Note: T he unit will save any changes and exit set mode after 30

seconds unattended.

To replace the battery:

1. Insert a coin into the slot on the

bottom of the case, and twist to

loosen the faceplate. Remove

faceplate and set aside.

2. Locate the battery holder as seen

on sketch. Pull out the old battery,

and push a new LR-44 battery into the holder,

with positive terminal (+) facing up.

3. Snap faceplate back into place, hooking the bottom

two tabs first, then closing by pressing together at the

top two tabs.

OTHER SETTINGS

The Step Filter and Unit of Measurement settings are

accessed through a special "deep set" mode.

To enter this mode, press and hold the S1 (MEMORY) button

for 4 seconds. T he screen will display a single digit. From

within Deep Set mode, press the S2 (MEMORY) button to

cycle back and forth between the Step Filter set point and

Choice of Unit System.

"US" (English)

or "EU" (Metric)

STEP TIME

190

JW200

S3-

Set measurement mode

REPLACING THE BATTERY AND MASTER RESET

When the display starts to dim or goes blank, it is time to

replace the battery.

If the display is not uniformly dim or blank, and appears to

display "erroneous data" , do a Master Reset by pressing all

3 buttons simultaneously for 3 seconds and then release.

The display should go blank, then turn all segments on, then

display 0 steps in Step Mode.

Note: All the settings will return to their default setting values.

If you need to change the battery, the settings will also revert

to default settings.

SPECIFICATIONS, FEATURES, and FUNCTIONS

Description of Functions

• Counts Steps up to 99,999 then rollover.

• Has a T otal Memory for Steps that counts up to 99,999,999

steps, then rollover.

• Counts T ime spent in step activity, up to 999 Min 59 sec,

Battery

then rollover. Automatically counts whenever step activity

is occurring.

• Has a T otal Memory for Activity T ime that counts up to

99,999 minutes, then rollover.

• Counts distance traveled during step activity, up to

999.99 mi or km, then rollover. Automatically counts

whenever step activity is occurring.

Can be set

STEP TIME

from 0-5

steps

IGI

ALKER

.COM

190

DIST CAL

JW200

Set Step Filter set point

S1,S2,S4

S3+

IGI

ALKER

.COM

DIST CAL

S3-

S1,S2,S4

S3+