Sharp AR-M208 Servicehandleiding - Pagina 16

Blader online of download pdf Servicehandleiding voor {categorie_naam} Sharp AR-M208. Sharp AR-M208 32 pagina's. Digital laser copier/ printer
Ook voor Sharp AR-M208: Gebruikershandleiding (24 pagina's)

Pagina afdrukken

(Initial screen)

(Executing screen)

Sim3-3 OUTPUT CHECK

1:JGM1

4:FM-1200

7:STM

2:JGM2

5:EVM

8:OGSLR

3:FM-600 6:OFM

9:OGSLL

1/3

EXEC

2/3

During execution, [EXEC] is highlighted. Under this state, press the

[BACK] key to interrupt the operation.

Side guide plate drive motor

1:JGM1

Rear edge plate drive motor

2:JGM2

Finisher main motor (600dpi)

3:FM-600

Finisher main motot (1200dpi)

4:FM-1200

Tray lift-up motor

5:EVM

Tray offset motor

6:OFM

Staple operation motor

7:STM

Transport selection gate solenoid (R)

8:OGSLR

Transport selection gate solenoid (L)

9:OGSLL

Rear edge plate drive solenoid

10:JGSL1

Upper alignment plate drive solenoid

11:JGSL2

Shutter drive solenoid

12:SHTSL

Paper exit roller clutch

13:T2SCL

Paper holding solenoid

14:STGSL

The finisher main motor operates for 10sec, the staple motor 5 times,

the tray lift-up motor one reciprocating operation, other motors max. 20

reciprocating operations from the home position, the solenoid repeats

500msec ON and 500msec OFF 20 times.

The staple operation motor operates only when there is no cartridge

installed.

Note:Executable only when the finisher is installed.

8-1

Purpose

Adjustment/Operation test/check

Function

Used to check and adjust the operation of the

(Purpose)

developing bias voltage in each copy mode and the

control circuit.

Section

Image process (Photoconductor/Developing/Transfer/

Cleaning)

Developer/Toner hopper

Operation/procedure

After selecting the mode, enter the adjustment value and press the

[OK] key, and output will be made for 30sec.

(Initial screen)

(Input/Selection screen) (Executing screen)

Sim8-1 DV BIAS COPY

1:AE

400

5:SUPER PHOTO

2:TEXT

450

3:TEXT/PHOTO

450

1/2

EXEC [200-550]

Display items

Content

AE ( )

1:AE

Character

2:TEXT

Character/Photo

3:TEXT/PHOTO

Photo

4:PHOTO

Super photo

5:SUPER PHOTO *

Toner save

6:TONER SAVE

( ) Linked with the destinations of SIM 26-6.

Linked with the auto exposure mode of SIM 46-19-1.

* SUPER PHOTO (5:) cannot be executed.

When [OK] or [START] key is pressed, a caution buzzer sounds.

(Only the adjustment value can be entered.)

The minimum increment is 2V.

The result of (Set value – 199) / 2 is stored in the EEPROM.

10:JGSL1

11:JGSL2

12:SHTSL

EXEC

Disabled

Sim8-1 DV BIAS COPY

400

5:SUPER PHOTO

400

EXEC

[200-550]

400

Installation

Default

range

200-550

400 (–400V)

450 (–450V)

Disabled

376 (–376V)

AR-M208 SIMULATION 8 - 2

When reading a value from the EEPROM, the value of (EEP value *2)

+ 200 is used as the set value.

Therefore, the set value entered must be an even number. If an odd

number is entered the entered odd number + 1 is displayed after

pressing [OK] key.

8-2

Purpose

Adjustment/Operation test/check

Function

Used to check and adjust the operation of the main

(Purpose)

charger grid voltage (high mode) in each copy mode

and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/

Cleaning)

Photo conductor

Operation/procedure

After selecting the mode, enter the adjustment value and press the

[OK] key, and output will be made for 30sec.

The input value is in the increment of –25V.

(Initial screen)

(Input/Selection screen) (Executing screen)

Sim8-2 MHV(H) COPY

5:SUPER PHOTO

1:AE

2:TEXT

3:TEXT/PHOTO

1/2

EXEC [ 1- 8]

Display items

Content

AE ( )

1:AE

Character

2:TEXT

Character/Photo

3:TEXT/PHOTO

Photo

4:PHOTO

Super photo

5:SUPER PHOTO *

Toner save

6:TONER SAVE

( ) Linked with the destinations of SIM 26-6.

Linked with the auto exposure mode of SIM 46-19-1.

* SUPER PHOTO (5:) cannot be executed.

When [OK] or [START] key is pressed, a caution buzzer sounds.

(Only the adjustment value can be entered.)

NO.

Set value

Grid High

480

–480V

505

–505V

530

–530V

555

–555V

580

–580V

605

–605V

630

–630V

655

–655V

*1. The negative value of the set value corresponds to the grid high

output voltage.

*2. The set values can be selected from the above 8 patterns only.

*3. The selected pattern determines the grid high voltage and the grid

low voltage.

If, for example, the grid high voltage is set to –480V (pattern 1), the

grid low voltage is –350V.

8-3

Purpose

Adjustment/Operation test/check

Function

Used to check and adjust the operation of the main

(Purpose)

charger grid voltage (low mode) in each copy mode

and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/

Cleaning)

Photo conductor

Operation/procedure

After selecting the mode, enter the adjustment value and press the

[OK] key, and output will be made for 30sec.

Sim8-2 MHV(H) COPY

5:SUPER PHOTO

EXEC

[ 1- 8]

Setting

Default

range

1-8

3 (–530V)

5 (–580V)

Disabled

2 (–505V)

Grid Low

–350V

–375V

–400V

–425V

–450V

–475V

–500V

–525V