Crestron CLW-SLVS Gebruikershandleiding - Pagina 5

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Crestron CLW-SLVS. Crestron CLW-SLVS 6 pagina's. Stand-alone wall box switch

Pagina afdrukken

NOTE: The RED (Load) and BLACK (Hot) wires are

#14 AWG. The BLUE (Slave) and WHITE (Neutral)

wires are #18 AWG. The GREEN (Ground) wire is #16

AWG. The GRAY (Cresnet) wires are #22 AWG. The

BLACK wire (Cresnet ground) paired with the GRAY

(Cresnet) wires is #22 AWG.

CLW-SWS with CLW-SLVS Wiring

NOTE: The -SWS must be installed in the same wallbox

that contains the connections to the load.

The following wiring diagram illustrates installation of

the -SWS with a -SLVS.

Wiring Diagram of CLW-SWS with CLW-SLVS

CLW-SLVS

Hot

BLACK

BLUE

BLACK

LINE

120VAC

60Hz

WHITE

GREEN

WHITE

Ground

Neutral

NOTE: Do not connect the BLUE (Slave) wire to the

BLACK (Hot) or RED (Load) wires.

NOTE: The RED (Load) and BLACK (Hot) wires are

#14 AWG. The BLUE (Slave) and WHITE (Neutral)

wires are #18 AWG. The GREEN (Ground) wire is #16

AWG. The GRAY (Cresnet) wires are #22 AWG. The

BLACK wire (Cresnet ground) paired with the GRAY

(Cresnet) wires is #22 AWG.

NOTE: If a -SWS is installed without a -SLVS, the

BLUE lead (Slave) should be capped.

NOTE: The WHITE (Neutral) connection on the -SLVS

is optional and is only required for operation of the LED.

If the neutral is not available, the white lead should be

capped off.

5. Splice the gray wires of the -SW or -SWS to the

Class 2 low voltage wires connected to the

Crestron control system, a Crestron power

supply, or a Crestron connection block device.

Push the wires and the splices into a hole in the

drywall to provide the necessary separation.

6. Push all Class 1 Power wires back into the

wallbox and fasten the device to the wallbox

with the provided screws.

Installation Guide – DOC. 6134B

CLW-SWS

BLUE

BLACK

RED

GREEN

WHITE

GREEN

Ground

Cresnet

CLW-SW, SWS, & SLVS(W/A/B)

7. Attach decorative faceplate.

8. Restore power.

Operating Buttons and Switches

The -SW, -SWS, and -SLVS feature two pushbuttons (one

large, and one small). The -SW and -SWS also have a

three-position mode selection switch. The function of

each button is determined by the position of the mode

selection switch. Refer to the diagram below for the

location of the buttons and the switch.

Buttons of CLW-SW, -SWS, and -SLVS

Load

NOTE: The -SLVS does not have a mode selection

switch. It will act in the same mode as the -SWS.

OFF

When the mode selection switch is in the "OFF" position,

the buttons will not have any function and the load is

disconnected from the power source. This must be used

when changing light bulbs to ensure that the load is fully

disconnected from power.

ADJ

When the switch is in the ADJ position, the load can be

manually activated and deactivated by pressing the large

button. Pressing and holding the small button will set a

delay time for deactivating the load when the switch is in

the PRE position. To set the delay time, press and hold

the small button for the desired amount of time delay and

release the button. When the small button is released, the

LED will flash three times to confirm the time delay

setting. When done, return the switch to the PRE position.

NOTE: If a time delay is not set, the factory default is 10

seconds.

Stand Alone Wall Box Switch: CLW-SW, SWS, & SLVS • 5

Large Button

Small Button

Mode Selection Switch

(-SW & -SWS Only)