Epson 745c - PowerLite XGA LCD Projector Handmatig - Pagina 13

Blader online of download pdf Handmatig voor {categorie_naam} Epson 745c - PowerLite XGA LCD Projector. Epson 745c - PowerLite XGA LCD Projector 24 pagina's. Release of check tool for network projectors v1.00 for windows
Ook voor Epson 745c - PowerLite XGA LCD Projector: Gebruikershandleiding (42 pagina's), Bedieningshandleiding (36 pagina's), Handleiding voor snelle installatie (2 pagina's), Bedieningshandleiding (47 pagina's), Onderdelenlijst (1 pagina's), Product ondersteunings bulletin (30 pagina's), Snelle installatie (4 pagina's), Installatiehandleiding (19 pagina's), Gebruikershandleiding (1 pagina's), Technisch overzicht (7 pagina's), Product ondersteunings bulletin (25 pagina's), Product ondersteunings bulletin (38 pagina's), Product ondersteunings bulletin (12 pagina's), Product ondersteunings bulletin (42 pagina's), Product ondersteunings bulletin (22 pagina's), Product ondersteunings bulletin (28 pagina's), Product ondersteunings bulletin (41 pagina's), Product ondersteunings bulletin (34 pagina's), Product ondersteunings bulletin (38 pagina's), Product ondersteunings bulletin (28 pagina's), Product ondersteunings bulletin (15 pagina's), Product ondersteunings bulletin (22 pagina's), Snelle installatie (2 pagina's)

Pagina afdrukken
Epson 745c - PowerLite XGA LCD Projector Handmatig
3. Click the
button. Then click the
Configure
on the screen that appears. You see a screen like this:
4. Ad Hoc mode: Highlight
list and set the Value to
Access Point mode: Highlight
Value to
Infrastructure
5. Ad Hoc mode: Highlight
the name you gave the projector's ESSID (for example,
).
CONF ROOM
Access Point mode: Highlight
match the name assigned to the access point.
Note:
The SSID is case-sensitive.
6. Highlight
Encryption
7. Click the
tab and make sure the network card or
General
wireless network device is enabled.
8. Ad Hoc mode: Click
OK
properties dialog box. Then go to "Projecting Wirelessly"
on page 15.
Access Point mode: On the General tab, select
, then click the
Protocol
screen:
Advanced
in the Property
Network Type
.
802.11 Ad Hoc
and set the
Network Type
.
and set the Value to match
SSID
and set the Value to
SSID
and make sure it is disabled.
to close the network card's
Internet
button. You see this
Properties
tab
9. If your access point uses DHCP, select
automatically
and enter the required information.
address
❏
IP address
to the computer. It must be formatted like other
addresses on the network; usually the first three sections
(XXX.XXX.XXX) match the access point's IP address,
and the last section is unique.
❏
Subnet mask
this too must match how your network is set up.
❏
Default gateway
assigned to the access point when it was set up.
10. When done, click
11. Click the
Wireless Networks
Note:
If you don't see this tab, you may need to enable your wireless
card or network device by clicking
device settings; then follow any instructions on the screen to
enable the device.
8/04
Epson PowerLite 745c Projector
Obtain IP address
. Otherwise, select
Use the following IP
: Type in the IP address you want to assign
: For example, 255.255.255.000, but
: Enter the IP address that was
.
OK
tab. You see this screen:
Configure
Epson PowerLite 745c Projector
to access the
13
-