Acuity Brands Sensor Switch WSX PDT Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Acuity Brands Sensor Switch WSX PDT. Acuity Brands Sensor Switch WSX PDT 4 pagina's. Wall switch sensor w / convertible neutral / no neutral wiring, passive infrared (pir) or dual tech (pdt)

Pagina afdrukken

OPERATIONAL SETTINGS

NOTE: (
*
) Indicates factory default (unless otherwise marked)

2 = Occupancy Time Delay

Time sensor keeps lights on after last occupancy detection.
1 30 sec
4 7.5 min
7 15.0 min
2 2.5 min 5 10.0 min* 8 17.5 min
3 5.0 min 6 12.5 min 9 20.0 min
For additional time settings, contact technical support at
1.800.PASSIVE

3 = On Mode

Automatic On turns lights on when occupancy is detected. Manual
On requires a button press to turn the lights on. Reduced Turn-On
directs the sensor to only turn on when a large motion, such as
a person entering a room, is detected. Weaker signals, such
as reflections from glass, are ignored. Once lights are on, the
sensor returns to maximum sensitivity.
1 Automatic On
2 Manual On
Settings 1 & 3 not available on -VA (Vacancy only) sensors.
Notes on Default Settings
• WSX (PDT) Series default: Automatic On
• Default for units with -SA, -VA, or -NL option: Manual On
• WSX (PDT) 2P Series default: Pole 1 Auto On, Pole 2 Manual
• Default for 2P units with -2SA, -2VA, or NL options:
Both poles Manual On
4 = Switch Modes
These modes dictate switch functionality.
Pressing the button in Override Off mode (setting 1) turns off
and keeps lights off until pressed again.
Disabling the Switch (setting 2) prevents the button from turning
the lights on. (continued next column)

PROGRAMMING INSTRUCTIONS

Operational settings can be changed via the push-button sequence outlined below (note the example used is for changing occupancy time delay). Programming for 2P units done with each
pole's corresponding push-button.
1.
1.
5.
5.
While LED
flashes back new
setting 10x...
e.g., 4 flashes
indicates new
7.5 min time
delay setting
Sensor Switch 900 Northrop Road, Wallingford, CT 06492 Phone: 1.800.PASSIVE sensorswitch.com ©2013 Acuity Brands Lighting, Inc. All rights reserved 07/01/13
_________________________________________________________________________________________________
Predictive Mode (setting 3) determines if a user has left the room
after the lights are switched off. It does this by monitoring the
space for a period after the button is pressed (Predictive Grace
Time), following a delay to allow exiting the room (Predictive Exit
13 30.0 min
Time). If occupancy is detected the device will disable Auto-On
& hold the lights off until manually switched. If no occupancy is
detected the sensor instantly reverts to auto-on mode.
If Predictive Mode with Expiration (setting 4) is enabled, once
the sensor has disabled Auto-On it will continue to monitor the
space. When no occupancy is detected for a duration equal to the
occupancy time delay, the sensor will revert to Auto-On mode.
1 Override Off **
2 Switch Disable
3 Predictive Mode
4 Predictive Mode with Expiration*
*
Default for WSX (PDT) units & Pole 1 of WSX (PDT) 2P units
3 Reduced Turn-On
** Default for units with -SA, -VA, or -NL options, Pole 2 of WSX
(PDT) 2P units, and both poles of 2P units with -2SA, -2VA,
or -NL options
5 = Photocell Set-Point
The ambient light level at which the sensor prevents the lights
from initially turning on. Once on, the lights will remain on until
the occupancy time delay expires and turns them off.
1 Disabled*
2 Auto Setpoint
3 0.5 fc
4 1 fc
Note: Sensor changes to Auto On mode if photocell is enabled.
Photocell not present in -NL versions.
7 = LED Operation
Indicates behavior of device's LED.
1 Occupancy Indication*
2 Relay Indication
*Standard Factory Default
______________________________________________________________________________________
2.
Predictive
Occupancy
Grace
Time
Time
Delay
Predictive
Exit
Time
16x
2x
15x
3x
Microphone
Grace Period
13x
4x
Dual
12x
5x
Technology
PRESS BUTTON
(Microphonics
TM
)
11x
7x
10x
9x
Manual On
Grace
Operation
Period
Restore
Minimum
Factory
On Time
Defaults
6.
6.
Microphone
Grace Period
Technology
(Microphonics
5 2 fc
9 32 fc
6 4 fc
10 64 fc
7 8 fc
8 16 fc
3 Disabled
4 Override On***
*** Factory Default for -NL version
4.
3.
e.g., press 2x for
3.
Occupancy Time
Delay
On Mode
While LED
Switch
Mode
flashes
back current
setting 10x...
Photocell
Set-Pt
e.g., 5 flashes is default
LED
10 min time delay
Predictive
Occupancy
Grace
Time
Time
Delay
Predictive
Exit
On Mode
Time
16x
2x
15x
3x
Switch
13x
4x
Mode
Dual
12x
5x
Photocell
PRESS BUTTON
TM
)
Set-Pt
11x
7x
10x
9x
Manual On
LED
Grace
Operation
Period
Restore
Minimum
Factory
On Time
Defaults
WSX Family
9
= Restore Factory Defaults
Returns all functions to original settings.
1 Maintain Current*
2 Restore Defaults
10 = Minimum On Time
Required initial time for lamps to be on after each switch on,
regardless of occupancy status. Once met, lights resume
following occupancy time delay.
1 0 min (disabled)*
3 30 min
2 15 min
4 45 min
11 = Manual On Grace Period
Time period after lights automatically turn off that they can be
reactivated by motion. (Manual On (Semi-Auto) mode only)
1 0 sec
2 Unused
3 15 sec*
12 = Dual Technology (Microphonics
Relative responsiveness of Microphonics detection.
1 Normal*
3 Medium
5 Phase Off
2 Off
4 Low
13 = Microphone Grace Period
Time period after lights are automatically turned off that they
can be voice reactivated.
1 0 sec
3 20 sec
5 40 sec
2 10 sec*
4 30 sec
6 50 sec
15 = Predictive Exit Time
Time period after manually switching lights off for occupant to
leave the space.
1 5 sec
3 7 sec
5 9 sec
2 6 sec
4 8 sec
6 10 sec*
16 = Predictive Grace Time
Time period after Predictive Exit Time that sensor rescans the
room for remaining occupants.
1 0 sec
3 10 sec
5 30 sec*
2 5 sec
4 20 sec
6 40 sec
4.
30 min
20 min
13x
9x
8x
17.5 min
PRESS BUTTON
7x
6x
15.0 min
12.5 min
7.
7.
LED FLASHES
CONFIRMATION
TWICE
e.g., press 2x to
save and exit
5 60 min
)
TM
(15-10-5 min)
7 60 sec
7 15 sec
9 30 sec
8 20 sec
7 50 sec
8 60 sec
30 sec
1x
2.5 min
2x
3x
5.0 min
4x
5x
7.5 min
10 min
e.g., press 4x
to change
to 7.5 min
PROGRAMMING
COMPLETE
2 of 4