Acuity Brands Sensor Switch WSX PDT Краткое руководство по эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Переключатель Acuity Brands Sensor Switch WSX PDT. Acuity Brands Sensor Switch WSX PDT 4 страницы. Wall switch sensor w / convertible neutral / no neutral wiring, passive infrared (pir) or dual tech (pdt)

Печатать страницу

OPERATIONAL SETTINGS

NOTE: (

) Indicates factory default (unless otherwise marked)

2 = Occupancy Time Delay

Time sensor keeps lights on after last occupancy detection.

1 30 sec

4 7.5 min

7 15.0 min

2 2.5 min 5 10.0 min* 8 17.5 min

3 5.0 min 6 12.5 min 9 20.0 min

For additional time settings, contact technical support at

1.800.PASSIVE

3 = On Mode

Automatic On turns lights on when occupancy is detected. Manual

On requires a button press to turn the lights on. Reduced Turn-On

directs the sensor to only turn on when a large motion, such as

a person entering a room, is detected. Weaker signals, such

as reflections from glass, are ignored. Once lights are on, the

sensor returns to maximum sensitivity.

1 Automatic On

2 Manual On

Settings 1 & 3 not available on -VA (Vacancy only) sensors.

Notes on Default Settings

• WSX (PDT) Series default: Automatic On

• Default for units with -SA, -VA, or -NL option: Manual On

• WSX (PDT) 2P Series default: Pole 1 Auto On, Pole 2 Manual

• Default for 2P units with -2SA, -2VA, or NL options:

Both poles Manual On

4 = Switch Modes

These modes dictate switch functionality.

Pressing the button in Override Off mode (setting 1) turns off

and keeps lights off until pressed again.

Disabling the Switch (setting 2) prevents the button from turning

the lights on. (continued next column)

PROGRAMMING INSTRUCTIONS

Operational settings can be changed via the push-button sequence outlined below (note the example used is for changing occupancy time delay). Programming for 2P units done with each

pole's corresponding push-button.

While LED

flashes back new

setting 10x...

e.g., 4 flashes

indicates new

7.5 min time

delay setting

_________________________________________________________________________________________________

Predictive Mode (setting 3) determines if a user has left the room

after the lights are switched off. It does this by monitoring the

space for a period after the button is pressed (Predictive Grace

Time), following a delay to allow exiting the room (Predictive Exit

13 30.0 min

Time). If occupancy is detected the device will disable Auto-On

& hold the lights off until manually switched. If no occupancy is

detected the sensor instantly reverts to auto-on mode.

If Predictive Mode with Expiration (setting 4) is enabled, once

the sensor has disabled Auto-On it will continue to monitor the

space. When no occupancy is detected for a duration equal to the

occupancy time delay, the sensor will revert to Auto-On mode.

1 Override Off **

2 Switch Disable

3 Predictive Mode

4 Predictive Mode with Expiration*

Default for WSX (PDT) units & Pole 1 of WSX (PDT) 2P units

3 Reduced Turn-On

** Default for units with -SA, -VA, or -NL options, Pole 2 of WSX

(PDT) 2P units, and both poles of 2P units with -2SA, -2VA,

or -NL options

5 = Photocell Set-Point

The ambient light level at which the sensor prevents the lights

from initially turning on. Once on, the lights will remain on until

the occupancy time delay expires and turns them off.

1 Disabled*

2 Auto Setpoint

3 0.5 fc

4 1 fc

Note: Sensor changes to Auto On mode if photocell is enabled.

Photocell not present in -NL versions.

7 = LED Operation

Indicates behavior of device's LED.

1 Occupancy Indication*

2 Relay Indication

*Standard Factory Default

______________________________________________________________________________________

Predictive

Occupancy

Grace

Time

Delay

Predictive

Exit

Time

16x

15x

Microphone

Grace Period

13x

Dual

12x

Technology

PRESS BUTTON

(Microphonics

)

11x

10x

Manual On

Grace

Operation

Period

Restore

Minimum

Factory

On Time

Defaults

Microphone

Grace Period

Technology

(Microphonics

5 2 fc

9 32 fc

6 4 fc

10 64 fc

7 8 fc

8 16 fc

3 Disabled

4 Override On***

*** Factory Default for -NL version

e.g., press 2x for

Occupancy Time

Delay

On Mode

While LED

Switch

Mode

flashes

back current

setting 10x...

Photocell

Set-Pt

e.g., 5 flashes is default

LED

10 min time delay

Predictive

Occupancy

Grace

Time

Delay

Predictive

Exit

On Mode

Time

16x

15x

Switch

13x

Mode

Dual

12x

Photocell

PRESS BUTTON

)

Set-Pt

11x

10x

Manual On

LED

Grace

Operation

Period

Restore

Minimum

Factory

On Time

Defaults

WSX Family

= Restore Factory Defaults

Returns all functions to original settings.

1 Maintain Current*

2 Restore Defaults

10 = Minimum On Time

Required initial time for lamps to be on after each switch on,

regardless of occupancy status. Once met, lights resume

following occupancy time delay.

1 0 min (disabled)*

3 30 min

2 15 min

4 45 min

11 = Manual On Grace Period

Time period after lights automatically turn off that they can be

reactivated by motion. (Manual On (Semi-Auto) mode only)

1 0 sec

2 Unused

3 15 sec*

12 = Dual Technology (Microphonics

Relative responsiveness of Microphonics detection.

1 Normal*

3 Medium

5 Phase Off

2 Off

4 Low

13 = Microphone Grace Period

Time period after lights are automatically turned off that they

can be voice reactivated.

1 0 sec

3 20 sec

5 40 sec

2 10 sec*

4 30 sec

6 50 sec

15 = Predictive Exit Time

Time period after manually switching lights off for occupant to

leave the space.

1 5 sec

3 7 sec

5 9 sec

2 6 sec

4 8 sec

6 10 sec*

16 = Predictive Grace Time

Time period after Predictive Exit Time that sensor rescans the

room for remaining occupants.

1 0 sec

3 10 sec

5 30 sec*

2 5 sec

4 20 sec

6 40 sec

30 min

20 min

13x

17.5 min

PRESS BUTTON

15.0 min

12.5 min

LED FLASHES

CONFIRMATION

TWICE

e.g., press 2x to

save and exit

5 60 min

)

(15-10-5 min)

7 60 sec

7 15 sec

9 30 sec

8 20 sec

7 50 sec

8 60 sec

30 sec

2.5 min

5.0 min

7.5 min

10 min

e.g., press 4x

to change

to 7.5 min

PROGRAMMING

COMPLETE

2 of 4