Connecting Your EPSON Stylus Scan
1. Make sure both the printer and computer are turned off.
3. Plug the other end of the cable into your computer's parallel port.
Connect the EPSON Stylus Scan directly to the parallel
CAUTION
port on your computer. Do not use a pass-through port
on a Zip
®
drive or any other accessory. If your computer has more than one parallel
port, connect the printer to the built-in port (LPT1). To use a different port, see
your Windows help. For the fastest scanning and printing, enable your computer's
ECP/DMA mode, if possible. See your computer documentation for instructions.
Installing Your Driver Software
1. Turn on your computer and wait until you see the Windows desktop icons.
IMPORTANT: If at any time you see a message that Windows has detected
your printer and asking you to install a driver, ALWAYS select Cancel. You
can't install your printer software that way.
2. Insert the EPSON Stylus Scan 2000 Software CD-ROM.
3. Double-click My Computer on your screen.
4. Double-click the Epson_ss2000 CD-ROM icon. Then double-click Cdsetup.
5. Click the
Add Software button.
7. Follow the on-screen instructions to install the EPSON Smart Panel.
When installation is complete, you see the EPSON Stylus Scan
Setup Window.
8. Click Next.
In Windows 98, you see this window (if you don't see it, go to the next section):
When installation is complete, click OK to start the EPSON Screen Calibration
utility. Then follow the instructions in the next section.
Calibrating Your Screen and
Installing Adobe PhotoDeluxe
.
1
You should now see the EPSON Screen Calibration utility start box. Click Next.
2. Move the slider right or left until the stripes match as closely as possible.
Then click OK. When calibration is complete, the Acrobat Reader installation begins
automatically. Don't restart your computer until all programs have been installed.
3. Follow the on-screen instructions. After the installation is complete, click OK.
The WinFax installation begins. You may need to insert your Windows 95 or 98
CD-ROM, if you see a message requesting it. If you see a message requesting
"DLL Installations," click OK, click Browse, click OK, then click OK again.
4. Click OK to restart your computer.
5. Insert your PhotoDeluxe CD-ROM. Follow the instructions to accept the license
agreement and install PhotoDeluxe.
6. When you see a message asking to restart your computer, click OK.
Now you're ready to print, scan, and copy. See your User's Guide for instructions.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. General notice: Other
product names are for identification purposes only and may be trademarks of their respective owner. EPSON
disclaims any and all rights in those marks. Copyright ©1999 Epson America, Inc. Printed on recycled paper
with at least 10% post-consumer content.
2. Plug the parallel cable into
the printer's parallel connector,
then fasten it with the wire clips.
6. Click OK.
9. Select LPT (Printer Port), then
click Next.
CPD 8878
Macintosh with USB:
Making the connection
Before connecting the EPSON Stylus Scan to your Macintosh, you must first
install the software.
To connect the printer, you'll need a shielded USB "AB" interface cable, not
more than 6.5 feet long.
NOTE FOR iMAC
™
installing the EPSON Stylus Scan software. This update is available online from
the Apple
®
Web site. If you're running Mac OS 8.5 or later, Apple recommends
that you install iMac Update 1.1.
Installing the Software
1. Turn on your Macintosh and make sure any virus protection programs are
turned off.
2. Insert the EPSON Stylus Scan 2000 Software CD-ROM.
3. Double-click the EPSON SS2000 icon to open the CD-ROM.
4. To install EPSON Personal Copy, Presto!
Acrobat Reader, double-click the appropriate folder. Then double-click the
or Disk 1 folder (if necessary), and double-click the corresponding installer
icon. Follow the on-screen instructions.
5. After all applications have been installed, double-click the EPSON Stylus Scan
Drivers folder.
6. Double-click the EPSON Stylus Scan 2000 icon.
8. When you see a message asking to restart your Macintosh, click Restart.
The EPSON Screen Calibration utility starts automatically.
9. Move the slider right or left until the stripes match as closely as
possible. Then click OK.
Your Macintosh restarts. Follow the instructions in the next section to install
Adobe PhotoDeluxe.
Installing Adobe PhotoDeluxe
1. Insert your PhotoDeluxe CD-ROM.
2. Double-click the Installer icon.
3. Follow the instructions on the screen to accept the license agreement and
install PhotoDeluxe.
4. When you see a message asking to restart your Macintosh, click OK.
Follow the instructions in the next section to connect your EPSON Stylus
Scan and select it in the Chooser.
Connecting Your EPSON Stylus Scan and
Selecting It in the Chooser
1. Turn on the EPSON Stylus Scan by pressing the
2. Connect the square end of the USB
3. Connect the flat end of the cable to the USB port on your Macintosh or your
USB hub port.
If you're using a USB hub, connect the printer to a first
CAUTION
tier hub. If the printer doesn't work with the hub,
connect it directly to a USB port on your Macintosh.
4. Select Chooser from the Apple menu.
5. Click the
SS 2000
icon.
Now you're ready to print, scan, and copy. See your User's Guide for instructions.
®
If you're using Mac
OS 8.1, you need to
install the iMac Update 1.0 before
™
PageManager for EPSON, and
7. Click Install, then follow the on-
screen instructions. When you see
a message asking for your default
paper size, select LETTER, then
click OK.
power button.
cable to your printer's USB port.
6. Click the icon for
the USB port
you're using.
7. Turn on background
printing if you want
to use it.
8. Close the Chooser.
Pagina afdrukken