Acuity Brands Lithonia Lighting D-Series Wall Installatie-instructies - Pagina 4

Blader online of download pdf Installatie-instructies voor {categorie_naam} Acuity Brands Lithonia Lighting D-Series Wall. Acuity Brands Lithonia Lighting D-Series Wall 4 pagina's. Size 1 led light fixture

Pagina afdrukken

Installation Instructions

D-Series Size 1 LED Wall

Mounting the

D-Series Size 1 LED Wall

fixture to a back box (BBW):

Back box will be provided with (3) 3/4" NPT hole plugs, one on top and

on each side. (See Figure A).

See the back box in Figure B for the location of the cast-in drill point

indentations provided for Step 1 below.

Step 1: Drill the back box as shown in Figure B to prepare it for

1/4"anchor bolts (not provided) in 2 places with 9/32" drill.

Step 2: Place drilled back box against the wall, mark wall and drill for

the anchors (not provided).

Step 3: Install (2) anchors (not provided) securely into wall and attach

the back box. Install surface-mount conduit and secure with 3/4" NPT

locking nut (not provided). Do not over tighten.

Step 4: Secure green grounding wire from supply conductors to

grounding lug in back box.

Step 5: Apply bead of silicone sealant (not provided) around perimeter

of back box.

Step 6: Consult fixture installation instruction to complete installation.

Installing the

D-Series Size 1 LED Wall

Step 1: Take one of the wire guard brackets and place it against the edge of the cast housing. Locate the bracket hole 2-11/16" away from

the front of the housing as shown in Figure A. Use bracket as a drill guide. Use a #26 drill bit (.146 to .150 dia) and drill through in 2 places

taking care not to drill into the LED lights. Repeat these steps on the other side.

Step 2: Using a 1/4" hex drive, attach the wire guard brackets to the cast housing as shown in Figure B. The screws will create their own

threads in the holes you drilled in Step 1. Now take the remaining screws and attach the shield to the wire guard brackets.

2-11/16"

Edge of

casting

Installing the

D-Series Size 1 LED Wall

Step 1: Take one of the vandal guard brackets and place it against the edge of the cast housing. Locate the bracket hole 1-3/4" away from

the front of the housing as shown in Figure A. Use bracket as a drill guide. Use a #26 drill bit (.146 to .150 dia) and drill through in 2 places

taking care not to drill into the LED lights. Repeat these steps on the other side.

Step 2: Using a 1/4" hex drive, attach the vandal guard brackets to the cast housing as shown in Figure B. The screws will create their own

threads in the holes you drilled in Step 1.

Step 3: Take the vandal guard plastic shield and remove any protective film that it may have been shipped with. Now take the remaining

screws and attach the shield to the vandal guard brackets.

1-3/4"

Edge of

casting

Troubleshooting: If this fixture fails to operate properly, check to make sure: • The fixture is wired correctly.

correctly.

• The line voltage at the fixture is correct. If all these variables have been checked and the fixture still does not operate as

specified, contact your local Lithonia Lighting distributor.

standard

Wire Guard

Wire guard

bracket

Figure A

Vandal Guard

Vandal guard

bracket

Figure A

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 800-279-8041 • Fax: 770.918.1209 •

Figure A

Top view

Figure B

drill point

5-1/2"

indentation

2-5/8"

4-3/8"

Figure B

www.lithonia.com

Side view

13/16"

11"

Figure B

• The fixture is grounded

Part Number:

RJ521349 Rev B

Revision Date: 6/3/14

1-3/4"

drill point

indentation