Epson PowerLite 1825 Gebruikershandleiding - Pagina 12

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Epson PowerLite 1825. Epson PowerLite 1825 14 pagina's. Release of check tool for network projectors v1.00 for windows
Ook voor Epson PowerLite 1825: Gebruikershandleiding (42 pagina's), Bedieningshandleiding (36 pagina's), Snelle installatie (2 pagina's), Bedieningshandleiding (47 pagina's), Conformiteitsverklaring (4 pagina's), Productspecificatie (2 pagina's), Onderdelenlijst (1 pagina's), Product ondersteunings bulletin (25 pagina's), Product ondersteunings bulletin (38 pagina's), Product ondersteunings bulletin (12 pagina's), Product ondersteunings bulletin (42 pagina's), Product ondersteunings bulletin (22 pagina's), Product ondersteunings bulletin (28 pagina's), Product ondersteunings bulletin (41 pagina's), Product ondersteunings bulletin (34 pagina's), Product ondersteunings bulletin (38 pagina's), Product ondersteunings bulletin (28 pagina's), Product ondersteunings bulletin (15 pagina's), Product ondersteunings bulletin (22 pagina's)

Pagina afdrukken
Epson PowerLite 1825 Gebruikershandleiding
PowerLite 1825
You can remove the air filter to clean both sides even if the
projector is mounted on the ceiling (see below).
3. If the dirt is difficult to remove or the filter is broken,
replace the filter as described below. Contact your dealer or
call Epson at 800-GO-EPSON (800-463-7766) to obtain a
new filter (part number V13H134A08).

Replacing the Lamp and Air Filter

The life span of the projection lamp is about 2,500 hours if
in the Settings menu is set to
Brightness Control
(default), and 3,000 hours if
Note: When you get a replacement lamp for your projector, you
should replace the filter. Turn off this product when not in use to
prolong the life of the projector.
It is time to replace the lamp when:
❏ The projected image gets darker or starts to deteriorate.
❏ The message
Replace the lamp
the lamp comes on and the lamp warning light
orange. To maintain projector brightness and image quality,
replace the lamp as soon as possible.
❏ The lamp warning light
out).
Lamp
warning
light
To obtain a new lamp, contact your dealer or call Epson at
800-GO-EPSON (800-463-7766). Request part number
V13H010L40.
12
Vent
Air filter
High
is set to
Brightness Control
appears on the screen when
flashes red (the lamp is burnt
Follow these steps to replace the lamp and air filter:
1. Turn off the projector and unplug the power cord.
2. Let the projector cool for at least an hour (if it has been on).
The lamp is extremely hot immediately after use.
Warning: Let the lamp cool fully before replacing it. In the
unlikely event that the lamp has broken, small glass fragments
may be present and should be removed carefully to avoid injury.
If the lamp is used after the replacement period has passed, the
possibility that the lamp may break increases. When a lamp
replacement message appears, replace the lamp with a new one
as soon as possible, even if it is still working.
3. Loosen (but don't remove) the lamp cover screw. Then slide
the lamp cover to the side and lift it off the projector.
4. Loosen the two screws holding the lamp in place.
.
Low
flashes
5. Hold the lamp as shown and pull it straight out.
Note:
consult your state and local regulations regarding disposal or
recycling. Do not put in the trash.
2/08
Loosen, but don't
remove these screws
The lamp(s) in this product contain mercury. Please