Dinex 611220 (208V/240V) Bedienings- en onderhoudshandleiding - Pagina 4

Blader online of download pdf Bedienings- en onderhoudshandleiding voor {categorie_naam} Dinex 611220 (208V/240V). Dinex 611220 (208V/240V) 8 pagina's. Induction base heating or change to cook-top mode for use with induction cooking pans.

Pagina afdrukken

cooktop. To get into cook mode, first remove the base

locator by lifting it straight up off the charger. Failure to

remove this may cause melting or other damage to it.

While charger is OFF, press the "POWER" button 3 times

within 10 seconds to activate Cook mode. The charger will

beep once to indicate it has entered the cooking mode.

When first entering cooking mode, it will be at minimum

power, so one(1) red LED will be lit. If you are in Smart-

Therm mode, no red LED's will be lit unless there is a valid

base charging on the charger. Use the up and down arrow

buttons to adjust the power level in 10% increments of

max power. The red LED's will light climbing from left to

right with each press of the up arrow. Full power is indi-

cated by having all ten(10) LED's lit. Pressing the down

arrow will turn off the LED's from right to left and reduce

the power.

Smart•Therm

™

charger

1. Do not at tempt to heat a Sm a rt • Th e rm base in coo k top mod e.

2. Do not at tempt to heat a Sm a rt • Th e rm base without base locato r.

INFO: If there is no heating for more than 30 seconds,

the power level will revert to the minimum power level 1.

3. If machine is idle for more than 3 minutes, the charger

will revert back to Smart•Therm™ mode.

4. If a Dinex® base is placed correctly on the charger

while in cooking mode, the charger will revert back to

Smart•Therm™ mode and proceed to automatically

heat the base to the required temperature.

5. Each evening before you close your operation, turn off

all Smart•Therm™ chargers by depressing the " POWER"

button. All membrane panel LED's will turn off.

INFO: The cooling fan will continue to run and will turn off

approximately 20 seconds after the power is turned off.

The unit will "auto-reset" when the power is turned off. The

fan will cycle and all 10 lights will flash.

Maintenance

S M A RT•THERM™ CHARGER CLEANING INSTRU C T I O N S

1 . Unplug the charger be fo re cleaning. Do not submerge the

c h a rger in wate r. Do not splash or pour water onto the

c h a rg e r' s co nt rol panel or into int a ke/outlet ve nt s. Po s s i b l e

s h ock hazard may result and the charger may be damaged.

2. The coo king surf a ce is a mate rial similar to te m p a red glass.

Please use appro p ri ate ca re in handling and cleaning.

locator

Page 4

3. Do not use steel wool or abra s i ve cleaners or chlori n ate d

cleaners on the charger.

4. Wi pe the ent i re charger off with a damp cloth and mild dete r-

g e nt . Dry the charger be fo re co n n e cting it to its elect ri cal source

WARNING: Never spray,wash or use exce s s i ve wa ter on the

Sm a rt • Therm induction charg e r.Be fo re cleaning it is absolute ly

n e ce s s a ry to unplug power plug.

• Do not use the cook-top if glass is broken or if

anything melts onto it.

• Always use approved coo kwa re when in coo k top mod e.

• Never use the coo k - top as a work surf a ce or cutting bo a rd.

• Never attempt to cook food dire ct ly on the glass surf a ce.

• Never attempt to heat aluminum fo i l .

4. AFTER WASHING SMART•THERM™ BASES, STORE IN

DINEX® DRYING RACK.

• IBDRS/90 - HOLDS 90 INDUCTION BASES

• IBDRS/180 - HOLDS 180 INDUCTION BASES

• IBDRS/270 - HOLDS 270 INDUCTION BASES

Troubleshooting

IMPORTANT: Safety-relevant parts should be replaced

with original factory parts only. Any defective parts must

be removed and replaced by a qualified service technician

authorized by Dinex®. Should you require service please

call the Dinex Hotline at 1-888-673-4639. In order for the

warranty to remain valid, work must be authorized by

Dinex® prior to being performed.

The Dinex® Smart•Therm™ Charger is a very intelligent

device. Built in diagnostics can help you to determine the

cause of most problems. The following section explains

how to determine if you are experiencing a problem and

what can be done to correct the problem. This informa-

tion can be very helpful if you are calling our Customer

Service department to report any operational difficulties.

1. Errors are indicated by a number of consecutive audible

"beeps" and the repeated flashing of the center 6

red lights.

2. If an error occurs, remove the base from the charger and

turn the charger OFF, wait 5 seconds, and turn the

charger back ON.

3. When the green "POWER" LED illuminates, place the

base back on the charger to continue charging.

4. If an error persists, remove the base from the charger,

turn the power off and unplug the charger, with the

charger unplugged press the "POWER" button (panel

LED's may momentarily flash), wait 5 seconds and then

plug the charger back in and turn the charger on by

pressing the "POWER" button.

5. When the green "POWER" LED illuminates, put the base

back on the charger to continue charging. Make sure

that the base is properly positioned on the charger.