dIXEL XW40L Installatie- en bedieningsinstructies - Pagina 3

Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} dIXEL XW40L. dIXEL XW40L 3 pagina's. Digital controller for medium-low temperature refrigeration applications

Pagina afdrukken

dIXEL

Installing and Operating Instructions

12. HOW TO USE THE HOT KEY

12.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD)

Program one controller with the front keypad.

When the controller is ON, insert the "Hot key" and push o key; the "uPL" message

appears followed a by flashing "End"

Push "SET" key and the End will stop flashing.

Turn OFF the instrument remove the "Hot Key", then turn it ON again.

NOTE: the "Err" message is displayed for failed programming. In this case push again o key if you

want to restart the upload again or remove the "Hot key" to abort the operation.

12.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY

(DOWNLOAD)

Turn OFF the instrument.

Insert a programmed "Hot Key" into the 5 PIN receptacle and then turn the Controller ON.

Automatically the parameter list of the "Hot Key" is downloaded into the Controller memory,

the "doL" message is blinking followed a by flashing "End".

After 10 seconds the instrument will restart working with the new parameters.

Remove the "Hot Key"..

NOTE the message "Err" is displayed for failed programming. In this case turn the unit off and then

on if you want to restart the download again or remove the "Hot key" to abort the operation.

13. ALARM SIGNALS

Message

Cause

"P1"

Room probe failure

"P2"

Evaporator probe failure

"HA"

Maximum temperature alarm

"LA"

Minimum temperature alarm

13.1 ALARM RECOVERY

Probe alarms P1", "P2", start some seconds after the fault in the related probe; they automatically

stop some seconds after the probe restarts normal operation. Check connections before replacing

the probe. Temperature alarms "HA", "LA" automatically stop as soon as the temperature returns to

normal values.

13.2 OTHER MESSAGES

Pon

Keyboard unlocked.

PoF

Keyboard locked

noP

In programming mode: none parameter is present in Pr1

On the display or in dP2, dP3, dP4: the selected probe is nor enabled

14. TECHNICAL DATA

Housing: self extinguishing ABS.

Case: facia 38x185 mm; depth 76mm

Mounting : panel mounting in a 150x31 mm panel cut-out with two screws.

Distance between the holes 165mm

Protection: IP20; Frontal protection: IP65 with frontal gasket mod RG-L. (optional)

Connections: Screw terminal block

2,5 mm

≤

Power supply: 230Vac or. 110Vac or 24Vac

Power absorption: 5VA max.

Display: 3 digits, 14,2 mm high; Inputs: 2 NTC probes.

Relay outputs: Total current on loads MAX. 20A

compressor: relay SPST 16(3)A, 250Vac

light: relay SPST 8 or 16(3) A, 250Vac

defrost: relay SPST 16(3) A, 250Vac

Other output : buzzer (optional)

Serial output : TTL standard; Communication protocol: Modbus - RTU

Data storing: on the non-volatile memory (EEPROM).

Kind of action: 1B; Pollution grade: 2;Software class: A.;

Rated impulsive voltage: 2500V; Over voltage Category: II

Operating temperature: 0÷60 °C; Storage temperature: -30÷85 °C.

Relative humidity: 20÷85% (no condensing)

Measuring and regulation range: NTC probe: -40÷110°C (-40÷230°F);

Resolution: 0,1 °C or 1°C or 1 °F (selectable); Accuracy (ambient temp. 25°C): ±0,7 °C ±1 digit

15. CONNECTIONS

Supply: 120Vac or 24Vac: connect to terminals 7-8

1598029050 XW40L NFR GB r1.0 11.07.2008.doc

Outputs

Compressor output acc. to par. "Con" and "COF"

Defrost end is timed

Outputs unchanged.

3 x 2mm.

∅

heat-resistant wiring and 6,3mm Faston

10%

16. DEFAULT SETTING VALUES

Label

Name

Set Set point

Hy Differential

LS Minimum set point

US Maximum set point

Ot Thermostat probe calibration

P2P Evaporator probe presence

OE Evaporator probe calibration

OdS Outputs delay at start up

AC Anti-short cycle delay

CCt Continuous cycle duration

CCS Set point for continuous cycle

COn Compressor ON time with faulty probe

COF Compressor OFF time with faulty probe 0 ÷ 255 min

CF Temperature measurement unit

rES Resolution

tdF Defrost type

dtE Defrost termination temperature

IdF Interval between defrost cycles

MdF (Maximum) length for defrost

dFd Displaying during defrost

dAd MAX display delay after defrost

Fdt Draining time

dPo First defrost after start-up

dAF Defrost delay after fast freezing

ALc Temperat. alarms configuration

ALU MAXIMUM temperature alarm

ALL Minimum temperature alarm

ALd Temperature alarm delay

dAO Delay of temperature alarm at start up

Adr Serial address

rEL Software release

Ptb Map code

Dixell S.p.A. Z.I. Via dell'Industria, 27

32010 Pieve d'Alpago (BL) ITALY

tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13

E-mail: [email protected] - http://www.dixell.com

XW40L

1598029050

Range

Value Level

LS÷US

0,1÷25.5°C/ 1÷ 255°F

-50°C÷SET/-58°F÷SET

-2

SET÷110°C/ SET ÷ 230°F

-12÷12°C /-120÷120°F

n=not present; Y=pres.

-12÷12°C /-120÷120°F

0÷255 min

0 ÷ 50 min

0.0÷24.0h

0.0

(-55.0÷150,0°C) (-67÷302°F)

0 ÷ 255 min

°C ÷ °F

°C

in=integer; dE= dec.point

EL=el. heater; in= hot gas

-50 ÷ 50 °C

8.0

1 ÷ 120 ore

0 ÷ 255 min

rt, it, SEt, DEF

0 ÷ 255 min

0÷120 min

n=after IdF; y=immed.

0 ÷ 23h e 50'

0.0

rE= related to set;

Ab = absolute

Set÷110.0°C; Set÷230°F

-50.0°C÷Set/ -58°F÷Set

0 ÷ 255 min

0 ÷ 23h e 50'

2.0

1÷247

1.8

---

Pr1

Pr2

Pr1

Pr2

Pr1

Pr2

3/3