Alton DW18903PR-6H Gebruiksaanwijzing - Pagina 8
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Alton DW18903PR-6H. Alton DW18903PR-6H 12 pagina's. 6gallon (23 l) portable wet/dry vacuum
English
Shut Down/Transportation (Fig. A)
1. Turn on/off control switch
2. Unplug the unit.
3. Store the power cord
2
bottom accessory box/cord wrap
4. When transporting in vehicles, secure the machine.
MAINTENANCE
Your ALTON appliance has been designed to operate
overa long period of time with a minimum of
maintenance.Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,before
adjusting or changing set-ups or when
making repairs.
An accidental start-up can cause
injury.
WARNING:
For user servicing, the machine must
be dismantled, cleaned and serviced, as far as is
reasonably practicable, without causing risk to the
maintenance staff and others. Suitable precautions
include, decontamination before dismantling, provision
for local ltered exhaust ventilation where the machine
is dismantled, cleaning of the maintenance area and
suitable personal protection.
• The manufacturer, or an instructed person, shall
perform a technical inspection at least annually,
consisting of, for example, inspection of the lter for
damage, air tightness of the machine and proper
function of the control mechanism.
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned, are to be disposed of; such items shall be
disposed of in impervious bags in accordance with
any current regulation for the disposal of such waste.
• For dust extractors it is necessary to provide for an
adequate air change rate L in the room if the exhaust
air is returned to the room.
(NOTE:
Reference to National Regulations is
necessary.)
Filter (Fig. A, I, J)
Filter care
The lters included with this vacuum are long life lters.
To be effective in minimizing dust recirculation, the lters
MUST be installed correctly and in good condition.
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling the lters.
To Remove Filters
1. Turn tool control power switch
position ( O ) and unplug cord from outlet.
2. Release lid latches
and remove vacuum
5
head
. from canister. Place vacuum head on a
4
level surface upside down.
3. Turn each lter
counterclockwise by gripping it on
9
to the OFF position.
3
wrapping it around the
.
8
3
to the OFF
the plastic end cover as shown, and carefully remove
from head, ensuring debris does not fall into mounting
hole.
NOTE:
Use care to not damage lter material.
4. If the bottom side of the vacuum head
be cleaned, use a cloth dampened with water and
mild soap and allow it to dry. Dispose of cloth in an
appropriate container.
5. Inspect lters for wear, tears or other damage.
NOTE:
If there is any doubt on the condition of the
lters they MUST be replaced. DO NOT continue use
if lters are damaged.
WARNING:
Never use compressed air or a brush
to clean lters, otherwise damage to the lter membrane
will occur which will allow dust to pass through the lter.
If needed, gently tap against a hard surface or rinse with
room temperature water and let air dry. Cleaning of the
lters is typically unnecessary, even if the lter is covered
with dust. The automatic lter cleaning system will
maintain maximum performance and continue to function.
If visual damage to the lter membrane exists, replace
lters. Filters typically last between six and twelve months
depending on use and care.
To Install Filters
1. Ensure lter seal
15
2. Line up lter threads
using moderate force, turn lter clockwise until tight.
NOTE:
Use care to not damage lter material.
3. Place the vacuum head
secure it by closing the lid latches
Assembly (Fig. F)
Wall Bracket Installation
1.Mark the wall according to the location of the wall
mount screws.
2.Punch holes in marked positions.
3.Tape the plastic expansion screws into the holes.
4.Align the wall mount with the holes and tighten the screws.
WARNING:
Inadequate mounting could allow the
unit to fall, causing injury and/or damage to the unit.
Installation of Accessory Bag Bracket
Press and hold the shrapnel of accessory bag bracket
align the wall bracket hole position, push the accessory
bag bracket
upward, until hearing the "click" sound,
18
and the installation is completed.
Attach Vac:
1. Grasp top handle
1
hand under front of tank.
2. Align tab on back of vacuum (located near top of tank)
to engage with slot in center of wall bracket as vacuum
is lowered into bracket.
3. Push downward making sure slots on vacuum
(located near the bottom of the tank) attach to the tabs
located at bottom of bracket.
6
needs to
4
is in place and is secure.
to vacuum head threads and
16
onto the container and
4
.
5
17
:
with one hand and place other
:
18
,
18