Alton DW18903PR-6H Manual de instruções - Página 8

Procurar online ou descarregar pdf Manual de instruções para Aspirador de pó Alton DW18903PR-6H. Alton DW18903PR-6H 12 páginas. 6gallon (23 l) portable wet/dry vacuum

Imprimir página

English

Shut Down/Transportation (Fig. A)

1. Turn on/off control switch

2. Unplug the unit.

3. Store the power cord

bottom accessory box/cord wrap

4. When transporting in vehicles, secure the machine.

MAINTENANCE

Your ALTON appliance has been designed to operate

overa long period of time with a minimum of

maintenance.Continuous satisfactory operation

depends upon proper appliance care and regular

cleaning.

WARNING: To reduce the risk of injury,

turn appliance off and disconnect

appliance from power source before

installing and removing accessories,before

adjusting or changing set-ups or when

making repairs.

An accidental start-up can cause

injury.

WARNING:

For user servicing, the machine must

be dismantled, cleaned and serviced, as far as is

reasonably practicable, without causing risk to the

maintenance staff and others. Suitable precautions

include, decontamination before dismantling, provision

for local ltered exhaust ventilation where the machine

is dismantled, cleaning of the maintenance area and

suitable personal protection.

• The manufacturer, or an instructed person, shall

perform a technical inspection at least annually,

consisting of, for example, inspection of the lter for

damage, air tightness of the machine and proper

function of the control mechanism.

• When carrying out service or repair operations, all

contaminated items which cannot be satisfactorily

cleaned, are to be disposed of; such items shall be

disposed of in impervious bags in accordance with

any current regulation for the disposal of such waste.

• For dust extractors it is necessary to provide for an

adequate air change rate L in the room if the exhaust

air is returned to the room.

(NOTE:

Reference to National Regulations is

necessary.)

Filter (Fig. A, I, J)

Filter care

The lters included with this vacuum are long life lters.

To be effective in minimizing dust recirculation, the lters

MUST be installed correctly and in good condition.

WARNING:

Appropriate personal protective

equipment like dust mask and gloves should be used

while handling the lters.

To Remove Filters

1. Turn tool control power switch

position ( O ) and unplug cord from outlet.

2. Release lid latches

and remove vacuum

head

. from canister. Place vacuum head on a

level surface upside down.

3. Turn each lter

counterclockwise by gripping it on

to the OFF position.

wrapping it around the

to the OFF

the plastic end cover as shown, and carefully remove

from head, ensuring debris does not fall into mounting

hole.

NOTE:

Use care to not damage lter material.

4. If the bottom side of the vacuum head

be cleaned, use a cloth dampened with water and

mild soap and allow it to dry. Dispose of cloth in an

appropriate container.

5. Inspect lters for wear, tears or other damage.

NOTE:

If there is any doubt on the condition of the

lters they MUST be replaced. DO NOT continue use

if lters are damaged.

WARNING:

Never use compressed air or a brush

to clean lters, otherwise damage to the lter membrane

will occur which will allow dust to pass through the lter.

If needed, gently tap against a hard surface or rinse with

room temperature water and let air dry. Cleaning of the

lters is typically unnecessary, even if the lter is covered

with dust. The automatic lter cleaning system will

maintain maximum performance and continue to function.

If visual damage to the lter membrane exists, replace

lters. Filters typically last between six and twelve months

depending on use and care.

To Install Filters

1. Ensure lter seal

2. Line up lter threads

using moderate force, turn lter clockwise until tight.

NOTE:

Use care to not damage lter material.

3. Place the vacuum head

secure it by closing the lid latches

Assembly (Fig. F)

Wall Bracket Installation

1.Mark the wall according to the location of the wall

mount screws.

2.Punch holes in marked positions.

3.Tape the plastic expansion screws into the holes.

4.Align the wall mount with the holes and tighten the screws.

WARNING:

Inadequate mounting could allow the

unit to fall, causing injury and/or damage to the unit.

Installation of Accessory Bag Bracket

Press and hold the shrapnel of accessory bag bracket

align the wall bracket hole position, push the accessory

bag bracket

upward, until hearing the "click" sound,

and the installation is completed.

Attach Vac:

1. Grasp top handle

hand under front of tank.

2. Align tab on back of vacuum (located near top of tank)

to engage with slot in center of wall bracket as vacuum

is lowered into bracket.

3. Push downward making sure slots on vacuum

(located near the bottom of the tank) attach to the tabs

located at bottom of bracket.

needs to

is in place and is secure.

to vacuum head threads and

onto the container and

with one hand and place other