ClearWater Lights Darla Installatiehandleiding - Pagina 10
Blader online of download pdf Installatiehandleiding voor {categorie_naam} ClearWater Lights Darla. ClearWater Lights Darla 12 pagina's. Led light kit for bmw k1600gt
Ook voor ClearWater Lights Darla: Installatiehandleiding (12 pagina's), Installatiehandleiding (12 pagina's), Installatiehandleiding (12 pagina's), Installatiehandleiding (16 pagina's)
Pagina afdrukken
CANopener Controls & Functions
TSC = Turn Signal Cancel WW = Wonder Wheel (BMW multifunction controller)
TPM = Tire Pressure Monitor FTP = Flash To Pass OBL = Optional Brake Light
Function
Darla/Glenda
Dimmer
[Pg. 5]
Erica/Krista/Sevina
Dimmer
[Pg. 5]
Erica/Krista/Sevina
On/Off
Darla On/Off
(Version 2.3 and later)
High
Beam
Mode
[Pg. 7]
Horn Activation
Mode
[Pg. 6]
Hazard
Flasher
Alert Mode
[Pg. 7]
Turn Signal
Dimming [Pg. 6]
(Starting Version 1.91)
Clearwater
Brake Light
(optional)
[Pg. 8]
Inertial
Braking
[Pg. 8-9]
Brake Dimming
Reset
Default
Settings
[Pg. 9]
CANopener Features Reference Sheet (As of 6/2/2020)
Current CANopener Version is 3.3
Default setting in
Command
Press and release TSC,
then Hold control wheel
Left for 2 seconds and
rotate to adjust. Press TSC
again to lock in.
Press and release TSC,
then hold control wheel
right for 2 seconds and
rotate to adjust. Press TSC
again to lock in.
Hold TSC for 2 seconds
Hold TSC Left for 5
seconds to turn OFF
Hold TSC Right for 3
seconds to turn back ON
Press and release TSC,
hold HAND brake lever and
press & release FTP 5
times to toggle
Press and release TSC,
then hold HAND brake
lever and press & release
TSC 5 times to toggle
Press and release TSC,
hold hazard switch then
press & release HAND
brake lever 5 times to
toggle
Press and release TSC,
hold right turn signal then
press & release HAND
brake lever 5 times
While stationary, press &
release TSC then casually
press & release the HAND
brake lever 5 times to
toggle
Press & release TSC then
press & release the FOOT
brake lever 5 times to
toggle
See Billy Brake Light
manual
Press and release TSC,
hold left turn signal then
press & release FTP 6
times
RED
Rotate WonderWheel to select 10 brightness levels (10%
to 100%) To adjust brightness on High Beam Mode, turn
on high beam first. Dimmer control will cancel after 2
seconds or by pressing TSC
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - all lights on 100% with high beam or FTP,
Krista/Erica/Sevina must be turned on
Mode 2 - Same as Mode 1 except Krista/Erica/Sevina
lights don't have to be turned on. (default)
Mode 3 - Same as Mode 2 but lights will strobe for 2
seconds if FTP is pressed 3 times (Version 1.91 and later)
Mode 1 - horn does not affect lights
Mode 2 - horn activates lights 100% (default)
Mode 3 - lights strobe with horn
Mode 1 - no flash (default)
Mode 2 - lights strobe while holding hazard switch
(Version 1.90 and earlier). Lights strobe when hazards are
toggled on (Version 1.91)
Mode 1 - off (default)
Mode 2 - lights dim when turn signals are activated.
Mode 1 - off (default on Version 1.6 and older)
Mode 2 - functions identically to BMW brake light (default
on Version 1.7 and later)
Mode 3 - California legal strobe on brake activation (4Hz
flash)
Mode 4 – speed sensitive (flashes faster and brighter with
harder braking) Can be adjusted.
Mode 1 - Inertial braking disabled
Mode 2 – Low sensitivity. Brake light activates when
engine braking reaches .4G.
Mode 3 – High sensitivity. Brake light activates when
engine braking reaches .2G. (default)
See Billy Brake Light manual
Reset all functions to the default settings above.
Page 9
Modes