ClearWater Lights Darla Kurulum Kılavuzu - Sayfa 10
Motosiklet Aksesuarları ClearWater Lights Darla için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. ClearWater Lights Darla 12 sayfaları. Led light kit for bmw k1600gt
Ayrıca ClearWater Lights Darla için: Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (16 sayfalar)
Sayfayı Yazdır
CANopener Controls & Functions
TSC = Turn Signal Cancel WW = Wonder Wheel (BMW multifunction controller)
TPM = Tire Pressure Monitor FTP = Flash To Pass OBL = Optional Brake Light
Function
Darla/Glenda
Dimmer
[Pg. 5]
Erica/Krista/Sevina
Dimmer
[Pg. 5]
Erica/Krista/Sevina
On/Off
Darla On/Off
(Version 2.3 and later)
High
Beam
Mode
[Pg. 7]
Horn Activation
Mode
[Pg. 6]
Hazard
Flasher
Alert Mode
[Pg. 7]
Turn Signal
Dimming [Pg. 6]
(Starting Version 1.91)
Clearwater
Brake Light
(optional)
[Pg. 8]
Inertial
Braking
[Pg. 8-9]
Brake Dimming
Reset
Default
Settings
[Pg. 9]
CANopener Features Reference Sheet (As of 6/2/2020)
Current CANopener Version is 3.3
Default setting in
Command
Press and release TSC,
then Hold control wheel
Left for 2 seconds and
rotate to adjust. Press TSC
again to lock in.
Press and release TSC,
then hold control wheel
right for 2 seconds and
rotate to adjust. Press TSC
again to lock in.
Hold TSC for 2 seconds
Hold TSC Left for 5
seconds to turn OFF
Hold TSC Right for 3
seconds to turn back ON
Press and release TSC,
hold HAND brake lever and
press & release FTP 5
times to toggle
Press and release TSC,
then hold HAND brake
lever and press & release
TSC 5 times to toggle
Press and release TSC,
hold hazard switch then
press & release HAND
brake lever 5 times to
toggle
Press and release TSC,
hold right turn signal then
press & release HAND
brake lever 5 times
While stationary, press &
release TSC then casually
press & release the HAND
brake lever 5 times to
toggle
Press & release TSC then
press & release the FOOT
brake lever 5 times to
toggle
See Billy Brake Light
manual
Press and release TSC,
hold left turn signal then
press & release FTP 6
times
RED
Rotate WonderWheel to select 10 brightness levels (10%
to 100%) To adjust brightness on High Beam Mode, turn
on high beam first. Dimmer control will cancel after 2
seconds or by pressing TSC
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - all lights on 100% with high beam or FTP,
Krista/Erica/Sevina must be turned on
Mode 2 - Same as Mode 1 except Krista/Erica/Sevina
lights don't have to be turned on. (default)
Mode 3 - Same as Mode 2 but lights will strobe for 2
seconds if FTP is pressed 3 times (Version 1.91 and later)
Mode 1 - horn does not affect lights
Mode 2 - horn activates lights 100% (default)
Mode 3 - lights strobe with horn
Mode 1 - no flash (default)
Mode 2 - lights strobe while holding hazard switch
(Version 1.90 and earlier). Lights strobe when hazards are
toggled on (Version 1.91)
Mode 1 - off (default)
Mode 2 - lights dim when turn signals are activated.
Mode 1 - off (default on Version 1.6 and older)
Mode 2 - functions identically to BMW brake light (default
on Version 1.7 and later)
Mode 3 - California legal strobe on brake activation (4Hz
flash)
Mode 4 – speed sensitive (flashes faster and brighter with
harder braking) Can be adjusted.
Mode 1 - Inertial braking disabled
Mode 2 – Low sensitivity. Brake light activates when
engine braking reaches .4G.
Mode 3 – High sensitivity. Brake light activates when
engine braking reaches .2G. (default)
See Billy Brake Light manual
Reset all functions to the default settings above.
Page 9
Modes