Cypress Semiconductor MoBL CY62126EV30 Specificatieblad - Pagina 5

Blader online of download pdf Specificatieblad voor {categorie_naam} Cypress Semiconductor MoBL CY62126EV30. Cypress Semiconductor MoBL CY62126EV30 14 pagina's. 1-mbit (64k x 16) static ram

Pagina afdrukken

Switching Characteristics

[10, 11]
Over the Operating Range
Parameter
Read Cycle
t
Read Cycle Time
RC
t
Address to Data Valid
AA
t
Data Hold from Address Change
OHA
t
CE LOW to Data Valid
ACE
t
OE LOW to Data Valid
DOE
t
OE LOW to Low Z
LZOE
t
OE HIGH to High Z
HZOE
t
CE LOW to Low Z
LZCE
t
CE HIGH to High Z
HZCE
t
CE LOW to Power Up
PU
t
CE HIGH to Power Down
PD
t
BHE / BLE LOW to Data Valid
DBE
t
BHE / BLE LOW to Low Z
LZBE
t
BHE / BLE HIGH to High Z
HZBE
[14]
Write Cycle
t
Write Cycle Time
WC
t
CE LOW to Write End
SCE
t
Address Setup to Write End
AW
t
Address Hold from Write End
HA
t
Address Setup to Write Start
SA
t
WE Pulse Width
PWE
t
BHE / BLE Pulse Width
BW
t
Data Setup to Write End
SD
t
Data Hold from Write End
HD
t
WE LOW to High Z
HZWE
t
WE HIGH to Low Z
LZWE
Notes
10. Test conditions assume signal transition time of 3 ns or less, timing reference levels of V
specified I
/I
and 30-pF load capacitance.
OL
OH
11. AC timing parameters are subject to byte enable signals (BHE or BLE) not switching when chip is disabled. See
12. At any temperature and voltage condition, t
13. t
, t
, t
, and t
transitions are measured when the outputs enter a high impedance state.
HZOE
HZCE
HZBE
HZWE
14. The internal write time of the memory is defined by the overlap of WE, CE = V
these signals can terminate a write by going inactive. The data input setup and hold timing must refer to the edge of signal that terminates write.
Document #: 38-05486 Rev. *E
Description
[12]
[12, 13]
[12]
[12, 13]
[12]
[12, 13]
[12, 13]
[12]
is less than t
, t
is less than t
HZCE
LZCE
HZBE
45 ns (Industrial)
55 ns (Automotive)
Min
Max
Min
45
55
45
10
10
45
22
5
5
18
10
10
18
0
0
45
22
5
5
18
45
55
35
40
35
40
0
0
0
0
35
40
35
40
25
25
0
0
18
10
10
/2, input pulse levels of 0 to V
CC(typ)
application note AN13842
, t
is less than t
LZBE
HZOE
LZOE
, BHE, BLE or both = V
. All signals must be active to initiate a write and any of
IL
IL
®
MoBL
, CY62126EV30
Unit
Max
ns
55
ns
ns
55
ns
25
ns
ns
20
ns
ns
20
ns
ns
55
ns
25
ns
ns
20
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
20
ns
ns
, and output loading of the
CC(typ)
for further clarification.
, and t
is less than t
for any device.
HZWE
LZWE
Page 5 of 13
[+] Feedback