Astonica 40200806 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Fontanna zewnętrzna Astonica 40200806. Astonica 40200806 3 stron. Three tier fountain

Drukuj stronę

3. (SEE FIGURE 3) Connect parts (D) medium

basin, (E) top pedestal and (F) small basin

together. Thread the PVC tube from ﬁnial

top (G) through the fountain assembly of

parts (D, E & F).

4. Taking the fountain assembly, thread the PVC

tube into the center pedestal (C) align the tabs

and notches of the fountain assembly and

secure by twisting.

5. With help, carefully lift the fountain assembly

slightly, ﬁnd the PVC tube, and connect the

PVC tube to the top of the electric pump spout.

Align the tabs and notches and secure the

complete fountain assembly by twisting.

6. Plug the light connectors from the light ring (I)

to the connectors from the electric pump (H),

and then push them into the center pedestal

and under the light ring to hide and secure the

door (retained from step 2) back on the base

of the center pedestal (C).

7. (SEE FIGURE 4) Fill the large basin (A) with

water; if possible use distilled water to ﬁll

the fountain.

8. Plug the power cord from the transformer (J)

into properly grounded 120V AC outlet.

Adjust Speed of Water Flow

1. Unplug pump (H) from AC power outlet.

2. Move adjustment switch on pump (H)

toward "+" positive to increase water

ﬂow, or "-" to decrease water ﬂow.

Maintenance

1. Check water level periodically, add

water if necessary.

2. If water is not ﬂowing, check electric pump (H),

and the clear tubing (K) for clogs.

NOTE: Pump may build up calcium after a

long period of time and stop running when

tap water is used. Any calcium remover can

be used to clean pump.

Figure 3

Pedestal

Notch

Basin Tab

Figure 4

Grounded

Outlets

ELECTRICAL SAFETY INSTRUCTIONS

WARNING!

ELECTRICAL SHOCK. Read and understand all instructions. Failure to follow all

instructions listed below, may result in electrical shock, ﬁre and/or serious personal injury.

Grounding Instructions

This fountain must be plugged into a 3-wire, 3-prong outlet that is properly working and has

been installed and grounded in accordance with all local, state or federal codes and ordinances.

DANGER:

IMPROPER INSTALLATION OF THE GROUNDING PLUG CAN RESULT IN A RISK OF

ELECTRICAL SHOCK. Check with a qualiﬁed electrician or serviceman if the grounding instructions

are not completely understood, or if doubt as to weather the product is properly grounded. Do not

modify the plug provided; if it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed

electrician. Do not use any type of adapter with this product.

Outdoor Use Extension Cords

1. When product is used outdoors, use only extension cords marked for outdoor use.

2. Use only UL listed extension cords. Never use damaged or altered extension cords.

3. Follow extension cord manufacturer safety instruction.

Extension Cords

1. Make sure your extension cord is in good condition.

2. When using extension cords, be sure to use one heavy enough to carry the current your product

requires. An undersized cord will cause a drop in line voltage resulting in power loss and

overheating. Reference Table 1 at the bottom of the page for the correct size to use depending

on cord length and nameplate Ampere rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

Table 1. Minimum Recommended Extension Cord Gauge (AWG) Chart

SAVE THESE INSTRUCTIONS.

AMP Load

Volts Extension Cord Length

120V

25'

50'

100'

AWG

1-5

6-10

10-12

12-16

Not recommended

150'