Dahl VARIODOCK Podręcznik konserwacji - Strona 7

Przeglądaj online lub pobierz pdf Podręcznik konserwacji dla Stacja dokująca Dahl VARIODOCK. Dahl VARIODOCK 19 stron.

Maintenance interval and documentation

Date: ___________ Km: ________________

Once a year or as required you must:

Carefully remove the top section of the docking station (remove the two bolts on each side). See instructions on page 21.

Clean the docking station.

Clean the locking cylinder and locking pin and lubricate with light oil.

Remove the locking pin if there are any signs of corrosion or damage (art. no. 503535).

Adjust the steel wire to the locking pin, art. no. 502400, if necessary.

All steel wires must be examined for signs of wear or evidence of breaks. Replace if necessary.

When the maintenance light is activated, VarioDock must undergo maintenance within 200 uses. Order service kit with art. no. 503636 (see also pages 34-35).

Test whether the manual emergency release functions properly and if the emergency release tool is in the vehicle.

Check whether the wires are loose in the terminals and whether they are intact and insulated. Replace if necessary.

Test whether the electromagnet/solenoid functions correctly.

Test whether the micro switch, art. no. 503640, functions correctly.

Test whether the warning tone (high-pitched howl) is activated and functions correctly.

Test whether the light diodes in the control panel function correctly along with the warning tone.

Check whether any nuts, bolts or screws are loose or damaged. Tighten/replace if necessary. This also applies to the lock plate and its fitting under the wheelchair.

Maintenance carried out:

Replaced parts:

Stamp

Next maintenance:

Date: ___________

Maintenance manual, installation and user guide UK

User Guide – Operation of the VarioDock

Please refer to the description of VarioDock

on page 14. The user must read these instructions in full prior to using the equipment.

Securing the wheelchair in the VarioDock

in the control panel flashes or is lit! Therefore,

1. The user must be driven forward, but not into the

always check if the lock plate is properly engaged

docking station. Now the height of the wheelchair

in the docking station by trying to back the wheel-

must be adjusted on the control panel (it is the vehi-

chair out of the docking station before moving the

cle adapter/workshop that must specify the height

vehicle. (It must not be possible to back out of the

of the lock plate and write on the supplied sticker).

docking station without pressing the red button in

2. The VarioDock

is equipped with a control switch

the control panel).

which indicates whether the lock plate is properly

engaged in the docking station. As soon as the

Release from the VarioDock

locking plate touches the locking pin, a warning tone

1. When the vehicle has been brought to a halt, remove

is heard and the red LED (LED) in the control panel

the safety belt.

lights up until the locking plate is fully in place or the

2. Press the release button on the control panel

wheelchair is driven away from the docking station.

(see page 15, F), and the docking station will then

3. As an indication that the wheelchair is properly

automatically drive upwards to the original height.

secured, the warning tone will cease, the red diode

The locking pin is released for either 5 or 8 seconds

in the control panel will go out and the green diode

(optional). The red LED lights up and a warning

lamp (LED) will light up.

tone is heard. The locking pin is then automatically

4. By pressing the blue button on the control panel,

locked / activated again. Do not try to back out of

the docking station can be pulled down/tightened

the docking station until the red LED in the control

so that unwanted slack is reduced while driving.

panel, indicating the release position, is lit.

DO NOT press the green button to pull the docking

WARNING!

downwards, as the force which tightens the docking

Attempting to reverse the wheelchair before the

station is not regulated, which may cause damage to

red LED has been illuminated will result in blocking

the wheelchair.

the docking station's lock mechanism which makes

5. When the wheelchair is correctly secured, the safety

it impossible to reverse. If this happens repeat the

belt should be fitted and adjusted so that it fits the

above unlocking procedure.

user.

3. Move the wheelchair away from the docking station

Do not drive the vehicle whilst a wheelchair is

within the 5 or 8 second period.

being manoeuvred into position in the docking

station. In general, do not use the vehicle if the

If the locking pin is not released when you press the

wheelchair is not correctly secured, the warning

red button in the control panel

tone sounds and/or the red warning lamp (LED)

1. In the event of electrical failure, a manual emergen-

cy release is located at the front edge of the docking

station. Push the red release arm to one side and

hold it there while the wheelchair moves away.

2. An emergency release tool in red is delivered with

each VarioDock. This has to be pushed between the

lock plate of the wheelchair and the docking station

to release the wheelchair.

VarioDock

, seat belts and components should be

inspected at least once a year in accordance with the

maintenance interval and documentation.

Safety belts (Accessory for VarioDock

Safety belts must be inspected and cleaned regularly.

Replace belts or straps that have faded in the sun, are

worn at the edges, have tears or show clear signs of

wear. Components that are damaged or worn must

also be replaced. Avoid soiling the belts with chemi-

cals, polishing agents, oil or, in particular, battery acid.

Cleaning the belts:

Wash by hand with hot water and mild soap. Rinse

thoroughly with water and allow to dry in the shade.

Do not expose the belts to direct sunlight and never

use powerful cleaning agents.

Only moving metal parts that are not in contact with

belt webbing should be lubricated with light oil when

necessary, and, if so, very carefully. Never lubricate

inertia reels or other components that are part of

the safety belt. Never let the belt webbing come into

contact with oil or grease.

Dahl VarioDock™

)