Electric Co SI2200W Instrukcja obsługi - Strona 14
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Żelazo Electric Co SI2200W. Electric Co SI2200W 18 stron.
Drukuj stronę
- Place the iron on the vertical position, open the water fill cover (B),tilt the iron forward at
an angle of approximately 45° and pour water to fill the tank until it reaches the maximum
level mark, marked with the inscription "MAX" (L). Make sure it does not exceed the "MAX"
mark (L) indicated the tank. For this purpose, you can use the filling cup (N) supplied with
the appliance.
Note: it should use distilled water to fill up the tank.
- After filling the water tank, close the cover (B). The iron is now ready to be used.
Operation
- Place the appliance on the vertical resting position over a stable and flat surface and
connect it to the wall socket.
- Select the right temperature in accordance with the fabric type on the temperature
selector button (J).
- The temperature light (I) turns on indicating that the appliance is warming up, and will
turn off when the select temperature is reached.
- Adjust the steam output on button (C) according to the fabrics type to be ironed.
- The appliance is ready to be used.
- During operation, the temperature light (I) turns on and off repeatedly, indicating that the
thermostat maintains the selected temperature.
- After use, turn off the appliance by sliding the steam control button (C) to the off position
"
" and the temperature selector button (J) to the "MIN" position.
- Unplugged the appliance from the wall socket when finish ironing.
Temperature selection
- Select the temperature according with the international symbols for fabrics treatment or
according with the fabric type:
CAUTION – This symbol marked on the fabric label means that
the fabric may not be ironed.
Instructions on label
Low temperature ( )
Medium temperature (
)
Low temperature (
)
Note: if the cloth material and the correct temperature to iron are unknown, it is
Temperature selector
Type of fabric
button (J)
Nylon
Silk
Wool
Cotton
Linen
recommended to test ironing on a small part on the reverse side of the cloth.
Note: if it is being used a high temperature for ironing and it is necessary to change to a
lower temperature, place the temperature selector button (J) on a lower level and wait until
the temperature light (I) turns on.
Temperature selection for steam ironing
- In order to obtain an efficient steam output, turn the temperature selector button (J) to
the place indicated with the symbols "
- Once the temperature light (I) turns off the iron is ready to be used, slide the steam
control button (C) to the desired position, knowing that the symbol "0" means "no steam"
and the symbol "
" means "maximum steam".
- After use, slide the steam control button (C) to the position the off position "
Note: if the temperature selector button (J) is not positioned at the area indicated with the
symbols "
" and "
that the appliance has not heated up sufficiently so it can generate steam conveniently.
Ironing without steam
- Make sure that the steam control button (C) is on position off position "0 ".
- Select the desired temperature according with the fabrics type on the temperature
selector button (J).
Water spray
- The water spray can be used whenever desired at any temperature, as long as there is
enough water in the water tank. It allows moistening the fabrics, making easier to eliminate
creases.
Note: the first time the appliance is used and when it is not used for a long period of time, it
may be needed to press several times the spray button "
Steam boost
- The steam boost provides an extra amount of steam output to remove creases or make
folds, ironing lace, hanging clothes, curtains, among others.
- Turn the temperature selector button (J) to the "MAX" position because only this position
allows the perfect steam boost output.
- The temperature light (I) turns on indicating that the appliance is warming up, and will
turn off when the select temperature is reached.
- Raise the iron a few centimetres above the clothing and press the steam output button
(E) to release the steam boost.
- To achieve an optimum result wait about 5 seconds between each time the steam boost
button (E) is pressed. To avoid the any water leak from the appliance's soleplate (M), never
press the steam boost button (E) continuously for more than 5 seconds and allows an
interval of at least one minute before pressing it again.
Vertical ironing
- The vertical steam output is particularly useful to iron hanging clothes, curtains, suits,
among others.
27
28
" and "
".
" it may happen leakage of water through soleplate (M), what means
".
" (D), until water is released.