Electric Co SI2200W Instrukcja obsługi - Strona 15
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Żelazo Electric Co SI2200W. Electric Co SI2200W 18 stron.
Drukuj stronę
- Turn the temperature selector button (J) to the "MAX" position.
- The temperature light (I) turns on indicating that the appliance is warming up, and will
turn off when the select temperature is reached.
- Hang the cloth on a hanger or place it on vertical support, approach the appliance to the
cloth and press the steam boost button (E).
- To achieve an optimum result wait about 5 seconds between each time the steam boost
button (E) is pressed. To avoid the any water leak from the appliance's soleplate (M), never
press the steam button (E) continuously for more than 5 seconds and allows an interval of
at least one minute before pressing it again.
Anti-drip system
- This appliance is equipped with an anti-drip system that immediately stops the steam's
formation when the selected temperature is too low, avoiding water spots on clothing.
Anti-scale system
- This appliance is equipped with a special system inside the water tank that softens hard
water and prevents lime scale build up resulting from the high temperatures generated.
Note: the system is integrated and permanent, and does not require replacement. The
existence of this anti-scale system does not avoid completely the formation of the
limestone on the appliance.
Self-cleaning function
- The appliance will remain in best conditions if this function is performed regularly, at
least once every two weeks. Depending on the hardness of the water used it may be
necessary to perform this function more regularly, especially when flakes come out of the
soleplate (M) during ironing.
- Make sure the appliance is unplugged from the wall socket.
- Slide the steam output button (C) to the off position "0" and fill the water tank as
previously described in "Filling up the water tank", until its maximum level "MAX" (L).
Note: do not use vinegar neither any other kind of descaling agent in the deposit.
- Turn the temperature selector button (J) to the "MAX" position, place the appliance on
the vertical resting position and plug it to the wall socket.
- The temperature light (I) turns on indicating that the appliance is warming up, and will
turn off when the select temperature is reached.
- As soon as the temperature light (I) goes off, unplugged the appliance from the wall
socket, hold it horizontally over a sink or a washbasin, press the self-cleaning button (K)
and gently shake the iron
forwards and
eliminated through the soleplate's vents (M) with the expelled steam and water.
- Tilt the appliance forwards and backwards to completely empty the water tank.
- Release the button (K) as soon as the self-cleaning function stops.
Note: if any residues still come out through the steam vents of the base (M), repeat the
entire process of self-cleaning.
-
After self-cleaning, plug the appliance to the wall socket to
(M) dry.
After reaching the set temperature for ironing, unplug the appliance from the wall
socket and gently pass the base (M) on a clean and soft cloth, in order to clean up any
stains that have arisen with the process of self-cleaning.
- Place the appliance on the vertical resting position and allow it to cool down completely
before storing it.
backwards.
The limestone and minerals
heat up and let the soleplate
Auto shut off system
- The auto shut off system shuts off the heating of the appliance when it's left motionless
when plugged, in two specific situations:
- When the appliance is not used for approximately 30 seconds after being placed
horizontally;
- When the appliance is not used for approximately 8 minutes after being placed
vertically.
- After that motionless time (30 seconds after being placed horizontally or 8 minutes after
being placed vertically) the temperature light (I) starts flashing, giving the warning that the
heating of the iron has been disabled.
- To re-activate the heating of the iron, lift it or move it slightly. The temperature light (I)
lights up, indicating that the appliance is warming up and turns off when it reaches the set
temperature.
- As soon as the temperature light (I) turns off, the iron has reached the selected
temperature and it is ready to be used again.
- To prevent water leaking from soleplate (M) when the appliance is placed horizontally,
set the steam output button (C) to the off position "0".
Empting the water tank
- Unplug the appliance from the wall socket and open the water-fill cover (B).
- Slide the steam regulator button (C) to the off position "0 ".
- Turn the appliance upside down so that the water remaining in the water tank exits
trough the opening of the cover (B).
HINTS
- Before ironing, read all the fabric labels and follow the manufacturer's instructions,
presented through symbols, such as:
Do not iron
will be
- Sort out the clothes to be ironed according with the fabric type. This will minimize the
frequency of temperature adjustment for the different fabrics.
- If the cloth material and the correct temperature to iron are unknown, it is recommended
to test ironing on a small part on the reverse side. Start with a low temperature and
increase gradually.
- For delicate fabrics such as silk, wool, velvet, etc. it is recommended to iron the cloth's
reverse side or use a cloth between the fabric and the iron, to prevent shinny patches.
- It is recommend the use of low temperatures in clothes with unusual finishes (sequins,
embroidery, plush, etc.).
- If the fabric is a mixture of several fibres (for example 40% cotton and 60% synthetic),
place the temperature selector button (J) to a lower temperature level.
29
30
Iron at a
Iron at a
maximum
maximum
Iron
temperature of
temperature of
110º
150º
Iron at a
maximum
temperature of
200º