Draper Access FIT Series Instrukcja - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja dla Ekran projekcyjny Draper Access FIT Series. Draper Access FIT Series 4 stron. Electric projection screen 220v
Również dla Draper Access FIT Series: Instrukcja instalacji i obsługi (8 strony)

Draper Access FIT Series Instrukcja
Access Fit
Please Note: Screen limits are factory set for optimum performance of the
screen. A procedure is outlined below for minor tweaks, but any adjustment
POSITION
FUNCTION
of these limits may negatively affect the flatness of the screen surface and
could also void the warranty. Please check with Draper prior to resetting
DOWN
Set LOWER limit
screen limits.
CAUTION: Always be prepared to shut screen off manually when new
Set UPPER limit
UP
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
Normal Operation
CENTER
Back View of Wall Switch
To Motor
with
7¾"
(197mm)
Built-In
Low Voltage
5
11
/
"
Slide
16
Switch
2"
(144mm)
(51mm)
C
o
D
m
+
o
m
5V
w
o
3"
To Motor
DC
n
n
with
(76mm)
Built-In
Low Voltage
7
/
"
8
(22mm)
CAUTION: Be sure all switches are in "off" position before adjusting limit
switches.
/
"
5
4
/
"
7
(124mm)
8
8
Please note: When ordering a motor with internal Low Voltage Controller,
(16mm)
6
/
"
7
(164mm)
if the case ships separate from the "guts," the case includes the 25' cable and
16
Standard Motor Wiring is on the
special low voltage switch.
AUDIENCE LEFT END of Screen Case.
CASE LENGTH
CASE LENGTH
CASE LENGTH
18"
18"
18"
(457mm)
(457mm)
(457mm)
L*
L*
L*
/
"
11
16
(17mm)
*L = Varies
*L = Varies
*L = Varies
For minumum length of ceiling cutout: subtract 1¼" (32mm)
from case length (measured from outer edge of flanges).
For minimum width of cutout (front to back): see case width dimensions below.
**Leveling bracket is used to level the case and should NOT be used to support the weight of the unit.
The leveling bracket is screwed to the side of the case and remains stationary. Hardware used for leveling provided by others.
There are several knock-outs in the screen housing to allow the Leveling Bracket to be adjusted laterally up to 16" (40.6cm) in either direction.
Case Width Dimensions
7¾"
(197mm)
5
/
"
11
16
2"
(144mm)
(51mm)
3"
(76mm)
/
"
7
8
(22mm)
/
"
5
4
/
"
7
(124mm)
8
8
(16mm)
6
7
/
"
(164mm)
16
Standard Motor Wiring is on the
AUDIENCE LEFT END of Screen Case.
Limit Adjustments (Low Voltage Motors with Internal Low Voltage Controller)
Figure 10
Please Note: 5V DC must be
connected to be able to set
/
"
½"
7
16
limits using the wall switch.
(13mm)
(11mm)
POSITION
FUNCTION
Set LOWER limit
DOWN
5
/
"
Set UPPER limit
UP
1
U
8
p
(130mm)
Normal Operation
CENTER
/
"
5
8
Back View of Wall Switch
(16mm)
To Motor
with
Built-In
Low Voltage
Slide
Case Length Dimensions
Switch
C
o
m
¾"
¾"
¾"
+
18"
18"
18"
m
(457mm)
(457mm)
(457mm)
5V
o
To Motor
DC
(9mm)
(9mm)
(9mm)
n
with
Built-In
Low Voltage
Center
Center
Center
of Case
of Case
of Case
8"
8"
8"
(203mm)
(203mm)
(203mm)
Series V
Viewing Surface
/
"
½"
7
16
(13mm)
(11mm)
ACCESS FIT
5
/
"
1
8
(130mm)
/
"
5
8
(16mm)
Connect the ILT switch to the motor via the terminal blocks, or via the modular
Connect the ILT switch to the motor via the terminal blocks, or via the modular
1
1
port using four conductor modular cable. When using modular cable, the cable
port using four conductor modular cable. When using modular cable, the cable
connectors MUST NOT be crimped in reverse, as with standard telephone
connectors MUST NOT be crimped in reverse, as with standard telephone
(For a Dry Contacts Wiring Diagram, see page 4.)
(For a Dry Contacts Wiring Diagram, see page 4.)
cable.
cable.
Set the slide switch to the lower position. Press and hold the DOWN button on
Set the slide switch to the lower position. Press and hold the DOWN button on
2
2
theswitch to move the viewing surface to the desired lower limit. If the screen
theswitch to move the viewing surface to the desired lower limit. If the screen
moves in the opposite direction, release the DOWN button and press and hold
moves in the opposite direction, release the DOWN button and press and hold
down the STOP button for four seconds. This will reverse the operation of the
down the STOP button for four seconds. This will reverse the operation of the
UP and DOWN switches.
UP and DOWN switches.
Move slider switch into center position.Wait a couple of seconds.
Move slider switch into center position.Wait a couple of seconds.
3
3
Please Note: If you move the slider switch from down to up in one motion it
Please Note: If you move the slider switch from down to up in one motion it
sets the two limits in the same position.
sets the two limits in the same position.
Set the slide switch to the higher position. Move the viewing surface to desired
Set the slide switch to the higher position. Move the viewing surface to desired
4
4
upper limit by pressing and holding the UP button on wall switch.
upper limit by pressing and holding the UP button on wall switch.
Return the slide switch to the center position to return to normal operation.
Return the slide switch to the center position to return to normal operation.
5
5
ACCESS FIT
To set the viewing surface to an alternate format position, move the
To set the viewing surface to an alternate format position, move the
6
6
viewing surface to the desired position and press the STOP button. Press and
viewing surface to the desired position and press the STOP button. Press and
hold the STOP button for at least three seconds to record the position.
hold the STOP button for at least three seconds to record the position.
Please Note: Pressing and releasing the UP button on the switch will move
Please Note: Pressing and releasing the UP button on the switch will move
the screen to its upper limit. Pressing and releasing the DOWN button will
the screen to its upper limit. Pressing and releasing the DOWN button will
move the screen to its lower limit.
move the screen to its lower limit.
While the motor is in motion, pressing the STOP button for less than two
While the motor is in motion, pressing the STOP button for less than two
seconds will stop the viewing surface at its present position.
seconds will stop the viewing surface at its present position.
Once the motor is stopped, pressing the STOP button will move the viewing
Once the motor is stopped, pressing the STOP button will move the viewing
surface to its alternate format position.
surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or in mo-
Pressing and holding the STOP button, when the motor is at rest or in mo-
tion, for at least three seconds will record a new alternate format position.
tion, for at least three seconds will record a new alternate format position.
D
o
U
w
p
LEVELING BRACKET**
LEVELING BRACKET**
LEVELING BRACKET**
n
1
1
1
/
/
/
"
"
"
3
3
3
TYP
TYP
TYP
8
8
8
(35mm)
(35mm)
(35mm)
6
6
6
/
/
/
"
"
"
7
7
7
8
8
8
(175mm)
(175mm)
(175mm)
Series E
Viewing Surface
Mounting Bracket Dimensions
/
"
7
(11mm)
16
1
/
"
3
8
(35mm)
/
/
/
"
"
"
7
7
7
8
8
8
(22mm)
(22mm)
(22mm)
L*
L*
/
"
11
16
(17mm)
/
/
"
"
11
11
16
16
(17mm)
(17mm)
For minumum length of
ceiling cutout: subtract 1¼"
1
/
"
5
from case length (measured from
8
(41mm)
outer edge of flanges).
For minimum width of cutout
(front to back): see case width
dimensions below.
3
/
"
7
(98mm)
16
7 ½"
(191mm)
9 ¾" (
248mm)
page 3 of 4