Draper Clarion Instrukcje montażu

Przeglądaj online lub pobierz pdf Instrukcje montażu dla Ekran projekcyjny Draper Clarion. Draper Clarion 2 stron. Permanently tensioned projection screen
Również dla Draper Clarion: Instrukcje montażu (4 strony), Instrukcje montażu (4 strony), Instrukcje montażu (2 strony), Instrukcje montażu (3 strony)

Drukuj stronę

Clarion Permanently Tensioned Projection Screen by Draper

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

➂ Screen should be accessible for complete removal should fabric

become damaged or should other ser vice be required.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen frame or viewing surface.

➅ Operating switch(es), for electric tilting screens, packed separately in

screen carton. Do not dis card with packing material.

➆ Electric tilting mechanism operates on 110-120v, 60 hz. current.

➇ Tools Required: Medium (#2) Phillips Screwdriver, Carpenters Level,

Soft face (rubber) Hammer & Measuring Tape.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Assembly of "Knocked-Down" Screen

General—

➀ Assemble inner frame on large table or on ﬂ oor. Refer to exploded drawing on

page 2 as you read these instructions.

➁ Open cartons along the length, not at ends. Remove all pieces from the carton.

Lay out the four sections of the inner frame (top, bottom, left and right) with the

front sides facing up. (Back of frame is side with snaps.)

Please Note: The frame is labeled "Stage Left" and "Stage Right." Stage Left

means the left side side of the screen as it faces the audience, which is the right

side as you face the screen. When these instructions refer to the left or right side

of the screen, they refer to the left or right side as you face the screen.

➂ Screw the left and right sides to the top and bottom frame members using #6 x

1" screws through the two pre -drilled holes in each end of sides. Screws should

thread into the circular screw channels. Make sure frame as sem bly is square by

measuring across frame diagonals (see Fig. 1).

# 6 x 1

Pan Head

Screw

➃ Place and screw one corner gusset to the inner frame as sem bly at each corner

with (6) #8 x

" pan head screws. Screws pass through pre-punched holes in

gussets and thread into screw chan nel on inner frame (see Fig. 2).

➄ Connect horizontal brace and vertical brace using (2) #10 x

3). See page 2 for the various conﬁ gurations.

Assembly/Mounting Instructions

Caution

Figure 1

#8 x 3/8"

Pan Head

Screw

Corner Gusset

Figure 2

" screws (see Fig.

Form Clarion_Inst04

➅ Place bracing assembly inside the inner frame so the plates at each end

of braces are completely visible from the front. Make sure these braces are

per pen dic u lar to the inner frame sections. Insert #8 x

holes in these plates and into the screw channel on the inner frame (see Fig. 4).

The inner frame assembly is now complete.

Slot Receives Screw

Attachment of Viewing Surface

Two people should attach the viewing surface of large screens, to pre vent

pos si ble damage.

➀ Unroll the viewing surface from the core with the viewing side face down. Be

extremely careful to protect the viewing surface by un roll ing it onto a clean

cloth or paper.

➁ Place the inner frame assembly, with front side down, against the back of the

viewing surface. Make sure the top piece of frame cor re sponds with the top side

of the viewing surface.

➂ Pull border snaps on viewing surface around the inner frame and snap to the

back side of the frame. Engage the two snaps at each corner ﬁ rst, then go

along each side and engage the remaining snaps.

➃ Pivot the frame/fabric assembly up into a vertical position and in spect surface.

➄ Lay frame/fabric assembly with viewing surface up. Frame is ready for

installation of trim frames.

➅ Place the four trim sections next to the correct sides of the frame/fabric

assembly. The side trim sections will have connecting brackets lo cat ed in each

end. These brackets will align and hold the face of the trim sections together.

➆ Place the top and bottom trims over the top and bottom of the frame/fabric

assembly. (Do not slide the trim sections along the outside edges of the

frame/fabric assembly. Doing this could dam age the fabric viewing

surface.)

➇ Align and start en gage ment of bracket in the side trim with slot in top trim by

hand. Use rubber hammer to drive trims fully together. Repeat for the other

corners of screen (see Fig. 5).

➈ After all four corners of trims are connected, turn entire screen as sem bly over

so viewing surface is face down. Be sure to protect surface in this position.

➉ The trims must be fastened to the inner frame with #8 x

has predrilled holes in the back ﬂ ange. Start by screwing the cor ners together

ﬁ rst. It may be necessary to squeeze the trims together at corners to close any

gaps. Do this before screw ing trim to inner frame. Finish attaching trims along

their length with additional screws (see Fig. 6, top of page 2).

If you encounter any difﬁ culties installing or ser vic ing your Clarion

screen, call your dealer or Draper Inc., Spiceland, Indiana, (765)

Printed in U.S.A.

987-7999, fax (765) 987-7142 or e-mail [email protected].

#10-24 x 1/2"

Flat Head

Screw

See detail for

configuration

possibilities

Figure 3

" screws through the

#8 x 3/8"

Pan Head

Audience

Screw

Side

Base

Frame

Figure 4

Figure 5

" screws. Each trim