Draper Clarion Instrukcje montażu

Przeglądaj online lub pobierz pdf Instrukcje montażu dla Ekran projekcyjny Draper Clarion. Draper Clarion 2 stron. Permanently tensioned projection screen
Również dla Draper Clarion: Instrukcje montażu (2 strony), Instrukcje montażu (4 strony), Instrukcje montażu (4 strony), Instrukcje montażu (3 strony)

Drukuj stronę

Clarion Permanently Tensioned Projection Screen by Draper

① Read instructions through completely before proceeding.

② Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

③ When lifting assembled screen, do not lift at only one corner; lift at

both corners. Lifting by one corner could result in damage to the

screen frame, especially on large screens.

④ Screen should be accessible for complete removal should fabric become

damaged or should other ser vice be required.

⑤ Screen should be installed level (using a carpenter's level).

⑥ Nothing should be fastened to screen frame or viewing surface.

⑦ Make sure you have received all parts (see parts list below and exploded

diagram on page 2).

⑧ Installer is responsible for providing appropriate hardware for mounting.

⑨ Tools Required:

" Allen Wrench (included); #2 Phillips screwdriver.

Optional tools: Flat blade screwdriver or small putty knife.

⑩ The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Clarion—Hardware and Parts List

Wall Brackets - 2

Surface Retention

Extrusions- 4

Viewing Surface - 1

Frame Preparation

① Clean area and place frame assembly pieces face down. Insert frame

extrusion connectors into aluminum frame extrusions as indicated in

Figures 1 through 3. For easier assembly insert the inner connectors ﬁ rst.

Figure 1

Figure 3

Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.

Form Clarion_Inst12-R

Assembly/Mounting Instructions

Caution

Frame Extrusions - 4

Plastic Tubing - 4

Frame Extrusion

Connectors - 8

Figure 2

Please Note: If extrusion connec-

tors do not slide into frame extru-

sions, make sure that setscrews are

backed out enough to allow proper

clearance.

Printed in U.S.A.

② Make sure frame extrusion connectors are fully seated (see Fig. 4).

③ Secure connectors by tightening setscrews (see Fig. 5).

④ Repeat steps 1-3 for the remaining corners (see Fig. 6).

The Clarion has a precision cut mitered corner.

Please Note: If corner gaps exist (painted frame only) readjusting the frame

and/or applying a small bead of black silicone to ﬁ ll the gap is the best solu-

tion. Apply a very small bead of black silicone to area where frame gap exists.

Work silicone into gap (using your ﬁ nger or a cloth). Remove ALL silicone on

face of frame; only silicone inside gap should remain.

Caution: When lifting assembled screen, do not lift at only one corner; lift

at both corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

If you encounter any difﬁ culties installing or ser vic ing your Clarion screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.

Figure 4

Figure 5

Figure 6

(Continued on Page 2)