Alemlube O30060 Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pompa wodna Alemlube O30060. Alemlube O30060 17 stron. Oil pump

Drukuj stronę

Trouble Shooting

Problem

The pump doesn't work

Leak of pneumatic device

The pump is unstable

The pump can work, but the

output flow is low

Oil leaks through the air exhaust

If the pump has anything wrong, please contact Alemlube. We do not recommend that the customer repairs

the pump themselves.

Storage & Maintenance

Pumps are delivered in appropriate carton boxes. Packaging material should be properly disposed.

Handling and storage of the new pump does not require any special procedures.

However after the pump has been used, empty the used oil in the suction tube into an appropriate container.

This is done by overturning the pump.

The dust in compressed air can slow down and even block the motor cylinder.

The following steps may prevent this from happening:

1. Let in 50 gram of Vaseline oil or other lubricator from the air inlet hole weekly, operate the pump for several

minutes after having been lubricated.

2. Turn on the pump for several minutes until moving parts are fully lubricated.

3. You may repeat the above operation if necessary.

4. The above steps should be carried out on a weekly basis.

For the pumps that are attached with compressed air treatment equipment, please empty the water retained

in the reservoir of the filter-purger frequently.

For the pumps that are attached with a lubricator, please pay close attention to the lubricator's oil level and refill

with SAE 20, SAE 30 or antifreeze oil for extreme conditions when necessary.

NOTE: The user should perform only routine maintenance operations (such as filters, silencers, cleaning...)

with the pump in order not to damage it or compromise its safety. Contact Alemlube when the pump needs

further maintenance.

NSW/ACT

QLD/PNG

TEL: (02) 9939 0711

TEL: (07) 3889 8480

FAX: (02) 9939 0411

FAX: (07) 3889 8490

OWNER'S TECHNICAL MANUAL

Oil Transfer Kit with Meter & Trolley

Possible Causes

1. Insufficient air

2. Air obstruction

1. The intake valve is closed

2. The intake valve is blocked

A blockage in a hose, valve, or other device

Damage to Screw (5) or plate (8)

Insufficient oil supply

Damage to Piston (7) or gasket (9) or spring (10)

Insufficient oil supply

O-ring (3) Seal (16) (26) (28) (34) damage

Tube (36) damage

Piston (7) wear

O-ring (3) Seal (16) (26) (28) (34) damage

A blockage in a hose, valve

Silencer dirty or damage

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

Solutions

1. Increase air pressure

2. Clear air passage

3. Change voltage

1. Open the intake valve

2. Clean the intake valve

Release pressure & clean

Assess damage, repair or replace Screw (5)

or plate (8)

Replace oil drums to ensure adequate oil supply

Assess damage, repair or replace Piston (7)

or gasket (9) or spring (10)

Replace oil drums to ensure adequate oil supply

Change Corresponding O-ring or seal

Change tube (36)

Change piston (7)

O-ring (3) Seal(16) (26) (28) (34) damage

Release pressure & clean components

Substitute damaged elements

SA/NT

TEL: (08) 9209 3066

TEL: (08) 8241 7111

FAX: (08) 9209 3933

FAX: (08) 8241 7011

www.alemlube.co.nz

O30060

TEL: (09) 447 1007

FAX: (09) 447 1008