anko 43056125 Skrócona instrukcja obsługi - Strona 6
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Głośniki anko 43056125. anko 43056125 10 stron. Bluetooth party speaker
Drukuj stronę
Prepare the remote control
1
2
To insert the remote control batteries:
1. Open the battery compartment.
2. Insert 2 x AAA batteries with correct polarity (+/-) as indicated. The 2xAAA battery not
include in our products, please purchase from Authorized Seller.
3. Close the battery compartment.
Please Note:
If you are not going to use the remote for a long time, remove the batteries.
l
l
Do not use old and new or different type of batteries in combination.
Batteries contain chemical substances, so they should be disposed of properly.
Turn On
1. Connect the AC power cable and plug to the wall socket;
2. Press the "POWER" button to o "ON" status to power on the speaker.
The speaker will be powered by AC power and set the power switch on rear panel to ON
position.
3.Press the POWER button on the top panel or on the remote control to turn it into Standby
mode,Press the POWER button on the top panel or on the remote control to turn off the
speaker and get into Standby mode, press for a few seconds again to turn on the speaker.
Caution:
If you do not use this unit for a while, please switch the "POWER" button to "OFF" status,
and disconnect the AC power cable of this unit.
Charging the internal Battery
The speaker comes with a built-in rechargeable battery, follow the below steps to charge it:
1. Connect the power cable and plug to the wall socket on the rear
2.
Turn on the power ON/OFF button on rear and top panel, there is a
on the bottom left corner of the display panel, it will light up and slowly flash, that is being
charge.
3.When the battery indicator light on the top left corner of the display pane light up, the
battery is fully charged, then unplug the power cable to stop charging, both top and
bottom indicator light will turn off automatically.
Intrenal Battery Level indicator
1. When the battery is running out, the battery indicator light on the bottom left corner light
up and quickly flash.
2. During playing, if you hear a "DI" sound from the speaker means the battery is running
out and the speaker will turn off after 1 minute.
3.Please pay attention to the speaker sound, if the sound becomes abnormal, please
charge the internal battery on time to keep the battery life.
Note: please fully charge the product when it is not going to be used for a long time and
charge once a month to keep longer battery life.
3
panel to start charging
battery indicator light
9
4.Play
Basic key play operations
You can control play through following operations.
Key
Function
1.Press this previous button for previous track when playcing
music on USB or Bluetooth mode.
2.In FM mode, short press this button to adjust FM frequency
for 0.1MHz, or long press this button to search FM radio
from 108-87.5MHz automatically.
1.Press this PLAY/PAUSE button to play or pause the music
when playcing music on USB or Bluetooth mode.
2.Or press for a few seconds to disconnect the bluetooth if
speaker at Bluetooth mode.
Press this EQ button to switch the different music effect.
Note: It cannot switch if the BASS is on.
Press the POWER button to turn off the speaker and get into
Standby mode, press for a few seconds again to turn on the
speaker.
Insert the Line-in cable to external device.
Insert the USB driver to USB socket to play music.
1.Press this previous button for previous track when playing
2.In FM mode, short press this button to adjust FM frequency
Press this M button for function mode switching between
Bluetooth/AUX/USB/FM modes.
1.Turn this VOLUME knob for volume increase or decrease
when playing music, the display will show from U 00 to
U 40 .
.
2.Press this VOLUME knob for one time to turn to the echo
volume level of microphone if using wired microphone,
the display will show " E ", then turn the knob to adjust the
sound volume of microphone echo.
3.Press this VOLUME knob for twice to turn to the
volume level of microphone if using wired microphone,
the display will show " C ", then turn the knob to adjust the
sound volume of microphone.
4.Press this VOLUME knob for twice to turn to the volume
level of guitar if using wired guitar, the display will show
" C ", then turn the knob to adjust the sound volume of guitar.
Press this BASS button for turn on or off the bass strong effect.
Press this LED button for turn on and off, or switch the light
effect.
AC Input jack
Insert the 6.35 wired microphone to the MIC jack.
Insert the 6.35 Guitar to the GUITAR jack.
music on USB or Bluetootth mode.
for 0.1MHz, or long press this button to search FM radio
from 87.5-108MHz automatically.
10