Daintree GE current Tetra EdgeStrip HO GEBIH50-2 Instrukcja instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Oświetlenie zewnętrzne Daintree GE current Tetra EdgeStrip HO GEBIH50-2. Daintree GE current Tetra EdgeStrip HO GEBIH50-2 5 stron.

Drukuj stronę

Tetra

EdgeStrip HO

Design Guidelines

All guidelines are based on a 5 in. (127mm) deep sign

for Tetra

EdgeStrip High Output. When installing the

modules, it is typically recommended to install the

modules across the longest distance to allow for the

shortest light throw.

1 ft. (0.30 m)

1 ft.

EdgeStrip HO: 1 side

(0.30 m)

Modules/side: 1

2 ft.

EdgeStrip HO: 1 side

(0.61 m)

Modules/side: 1

3 ft.

EdgeStrip HO: 1 side

(0.91 m)

Modules/side: 1

4 ft.

EdgeStrip HO: 2 sides

(1.22 m)

Modules/side: 1

5 ft.

EdgeStrip HO: 2 sides

(1.52 m)

Modules/side: 1

6 ft.

EdgeStrip HO: 2 sides

(1.83 m)

Modules/side: 1

7 ft.

EdgeStrip HO: 1 side

(2.13 m)

Modules/side: 7

Retrofit Instructions

1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside and outside the

building. Ensure that the branch circuit supplying the existing transformer or ballast will be within the voltage ratings of the new LED

power supply, and have a current rating not exceeding 20A, or that permitted by applicable local, state, or country electrical codes

(whichever is less).

2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or fluorescent tubes; and

associated transformers and ballasts. Care should be taken not to break the existing neon or fluorescent tubes.

NOTE: Follow all federal and local regulations when disposing of neon tubing, fluorescent tubes, transformers and ballasts.

3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by applicable

local, state, or country electrical codes; a new disconnect switch must be installed.

4. (Existing Signs Only) Repair and seal any unused openings in the electrical enclosure. Openings greater than 12.7-mm (1/2-in)

diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk. Smaller openings may be sealed

with non-hardening caulk.

5. Using the layout guidelines above, determine required number of LED modules required to illuminate the sign.

6. A Tetra

24VDC Class 2 Power Supply, as listed below, must be used with this retrofit kit. Determine the number of Tetra

Power Supplies required to power the number of LED modules required to illuminate the sign, so as not to overload the Tetra

Class 2 Power Supply chosen.

7. Follow the instructions above to properly mount the LED modules

8. Connect the DC output of the power supply to the LED modules using the Electrical Connections instructions above.

9. Connect the power unit to the supply in accordance with the applicable local, state, and country electrical codes, and the instructions

found in the power supply installation guide.

10. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and country

electrical codes.

2 ft. (0.61 m)

3 ft. (0.91 m)

EdgeStrip HO: 1 side

Modules/side: 1

EdgeStrip HO: 1 side

Modules/side: 2

EdgeStrip HO: 2 sides

EdgeStrip HO: 1 side

Modules/side: 1

Modules/side: 3

EdgeStrip HO: 1 side

Modules/side: 4

EdgeStrip HO: 2 sides

EdgeStrip HO: 1 side

Modules/side: 2

Modules/side: 5

EdgeStrip HO: 2 sides

EdgeStrip HO: 1 side

Modules/side: 2

Modules/side: 6

EdgeStrip HO: 1 side

Modules/side: 7

2 inches

Height

4 ft. (1.22 m)

5 ft. (1.52 m)

EdgeStrip HO: 2 sides

Modules/side: 1

EdgeStrip HO: 1 side

EdgeStrip HO: 2 sides

Modules/side: 4

Modules/side: 2

EdgeStrip HO: 1 side

Modules/side: 4

Modules/side: 5

EdgeStrip HO: 2 sides

Modules/side: 4

EdgeStrip HO: 2 sides

Modules/side: 4

Modules/side: 5

EdgeStrip HO: 2 sides

Modules/side: 4

Modules/side: 5

EdgeStrip HO: 2 sides

Modules/side: 7

Installation Guide

A 2 in. (51 mm) border is

recommended along the

perimeter of the sign.

6 ft. (1.83 m)

7 ft. (2.13 m)

EdgeStrip HO: 2 sides

EdgeStrip HO: 1 side

Modules/side: 1

Modules/side: 7

EdgeStrip HO: 2 sides

EdgeStrip HO: 1 side

Modules/side: 2

Modules/side: 7

EdgeStrip HO: 1 side

Modules/side: 6

Modules/side: 7

EdgeStrip HO: 2 sides

Modules/side: 4

Modules/side: 7

EdgeStrip HO: 2 sides

Modules/side: 5

Modules/side: 7

EdgeStrip HO: 2 sides

Modules/side: 6

Modules/side: 7

EdgeStrip HO: 2 sides

Modules/side: 7

Not Recommended

Class 2