Daintree GE current Tetra EdgeStrip HO GEBIH50-2 Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Oświetlenie zewnętrzne Daintree GE current Tetra EdgeStrip HO GEBIH50-2. Daintree GE current Tetra EdgeStrip HO GEBIH50-2 5 stron.

Drukuj stronę

Tetra

EdgeStrip HO

Troubleshooting

Symptom

Row of modules does not light

Sign does not light

Individual modules do not light

Modules are dim

Maximum Loading per Tetra

Note: Load shall not

SKU

Rating

GEBIH71-2

24VDC,

GEBIH50-2

5.40W

GEBIH41-2

per module

GEBIH32-2

Maximum Remote Mounting Distance

20W Power Supply

80W Power Supply

100W Power Supply

180W Power Supply

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.

If you have any questions about these instructions or your specific application, please contact support at [email protected].

This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications.

Solution

• Check wire connections to power supply to ensure red stripe-to-red and white-to-black or blue connections.

• Check row-to-row polarity connections.

• Check input and output voltage and check power supply input/output connections.

• Check polarity connections.

• Remove module and replace with another working module.

• Ensure the overall length of the Tetra

• Ensure the length and gauge of the supply wire is equal to or below the recommended remote

mounting distance.

24 VDC Power Supply

25W

80W

Power Supply

Dimming Power Supply

Note: Load shall not

exceed 0.83A

exceed 3.3A

4 modules/

14 modules/

4ft.(1.22 m)

14 ft. (4.27 m)

18 AWG/0.82 mm

16 AWG/1.31 mm

Supply Wire

120 ft./36.6 m

20 ft./6.1 m

For the latest install guides for your product go to: www. LED.com

Conforms to the following standards:

IP66 rated: separate enclosure required for outdoor use, UL damp location rated

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without

notice. All values are design or typical values when measured under laboratory conditions.

SIGN097 (Rev 02/12/21) GE2027-2822

LED system does not exceed the maximum load.

100W

Power Supply

Note: Load shall not

exceed 4.0A

17 modules/

18 ft. (5.49 m)

14 AWG/2.08 mm

Supply Wire

–

25 ft./7.6 m

35 ft./10.6 m

25 ft./7.6 m

35 ft./10.6 m

25 ft./7.6 m

35 ft./10.6 m

III

Installation Guide

180W

300W

Power Supply

Note: Load shall not

exceed 3.8A per each

exceed 4.0A per each

(of 2) output channels

(of 3) output channels

16 modules/

17 modules/

16 ft. (4.88 m)

18ft. (5.49 m)

per output channel

32 modules/

51 modules/

32 ft. (9.75 m)

54 ft. (16.46 m)

per power supply

12 AWG/3.31 mm

Supply Wire

–

40 ft./12.1 m