Casio 2411 Podręcznik - Strona 5
Przeglądaj online lub pobierz pdf Podręcznik dla Oglądaj Casio 2411. Casio 2411 9 stron.
6. On the sending watch, press F to send
the displayed image.
WATCH
• The data send screen shown nearby
SEND
• The message OK appears momentarily
WATCH
• Pressing A during the above procedure
SEND
• After you are finished sending images,
O K
To receive an image
1. On the IR menu, use B or E to select
watch (
2. Press F to display the watch-to-watch
send menu.
3. Press B or E to display the watch-to-
WATCH
watch receive menu.
RECEIVE
4. Press F again to enter receive standby,
which is indicated by the screen nearby.
5. Align the IR ports of the two watches with
each other, and perform the send operation
on the sending watch.
• See "To send an image" for more
• The message OK appears momentarily,
• Pressing A during the above procedure
• After you are finished receiving images,
Communication Errors
Screen messages appear in the IR Mode to let you know when there is a
problem with data communication. When this happens, check the following to
find out what you need to do. Also, you can avoid data communication
problems by carefully observing the advice under "Communication
Precautions".
Communication Screen Messages
WATCH SEND NG
Data send or receive failed for some reason. Try
(Sender),
again.
WATCH RECEIVE NG
(Receiver)
PLAY FULL
Memory of the receiver is full. Delete data you no
longer need and try again.
REC FULL
Memory of the receiver may be full. Delete data
you no longer need and try again.
PLAY EMPTY
There are not recorded images in the memory of
the sender.
INTERCEPTION
Something is obstructing the path between the IR
ports. Data communication will resume if you
remove the obstruction within about six seconds.
If the problem is not corrected within about six
seconds, the error message changes to NG.
CONVERT
This message appears while a watch is
processing image data before sending it or after
receiving it.
Other Messages
PLAY ERROR
Some problem occurred while accessing flash
memory.
REC ERROR
Data cannot be written because some problem
occurred while accessing flash memory.
IR COM ERROR
Some problem occurred while accessing flash
memory.
• When one of the above three errors occurs, first try deleting all data in
flash memory. If this does not correct the problem, contact the store or
dealer where you purchased the watch.
WAIT SET NG
Some problem occurred while rewriting flash
memory data. Try performing the operation again.
appears while an image send operation
is in progress.
after the image send operation is
complete. Next, the watch returns to the
screen in step 4 of the above procedure.
displays the IR menu.
press D to return to the Timekeeping
Mode.
).
information.
followed by the received image. Next,
the watch returns to the screen in step 3
of the above procedure.
displays the IR menu.
press D to return to the Timekeeping
Mode.
Communication Precautions
• The two IR ports must be within 10cm (4 inches) and 30 degrees of each
other.
• Proper data communication may also be impossible if the two IR ports are
too close to each other.
• At an angle of 15 degrees or more, you may need to move the two IR ports
very close to each other.
• Do not move the watch while communication is in progress.
• Make sure there is nothing between the two IR ports that blocks the path of
the IR signal.
• Infrared communication may not be possible in areas where lighting is
bright, near a window, etc.
• In the case of inverter fluorescent lighting or other very strong light, try
turning off the light or move to an area where light is not shining directly
onto the infrared ports.
• An unrelated nearby IR data communication operation can interfere with
proper IR data communication.
• The maximum allowable distance between the IR ports may be less than
10cm when watch battery power is low.
• The watch automatically returns to the IR (IR Mode) menu about five
minutes after the image selection screen or receive standby screen is
displayed. If the point where five minutes elapse occurs while a data send/
receive operation is in progress, the operation continues until it is
complete, after which the watch automatically returns to the IR menu.
TIMEKEEPING
The Timekeeping Mode is the default mode of
Month – Day
the watch when you are not recording images,
Day of the
Year
using the stopwatch, etc.
week
• See "To set the time and date" about setting
the time and date, and for selecting either
' ‰ 1 6 - 3 ‰
12-hour or 24-hour timekeeping.
P
SAT
1 ‰ : 5 8
Note
You can also make watch time and date
35
settings on your computer using the link
PM
software that comes bundled with the watch.
indicator
See the WQV Link 2.0 user's manual on the
Seconds
CD-ROM that comes with the watch for more
Hour : Minutes
information.
To reset the second's count to zero
1. In the Timekeeping Mode, hold down A for about one second until the
second's digits start to flash, which indicates the setting screen.
2. Press E to reset the second's count to 00.
• Pressing E while the second's count is in the range of 30 to 59 resets
the seconds to 00 and add 1 to the minutes. In the range of 00 to 29,
the minute's count is unchanged.
3. Press A to exit the setting screen.
To specify the wake up screen image
1. In the Timekeeping Mode, hold down A
for about one second until the second's
digits start to flash, which indicates the
CASIO
setting screen.
2. Press C to display the wake up screen
image setting screen.
3. Use E and B to scroll through images in
watch memory.
• Holding down either button scrolls at
• "CASIO" appears if there are no
4. Press A to exit the setting screen.
Using the Calendar Screen
The Calendar screen shows holidays and
Year / Month
other information for a full month at a glance.
• Pressing B or E while in the Timekeeping
Mode displays the Calendar screen.
• Press D to return from the Calendar screen
2 ‰ ‰ 1 / 6
to the Timekeeping Mode.
• You can turn holiday highlighting on and off
using the procedure under "To turn holiday
highlighting on and off" below.
Today
To view the calendar of a specific month
1. In the Timekeeping Mode, press B or E to display the Calendar screen.
• The current month appears first, with today's date flashing (according to
Timekeeping Mode time and date).
2. Use E (+) and B (–) to scroll through months until the one you want is
displayed.
• Holding down either button scrolls at high speed.
• The full-auto calendar automatically makes adjustments for month
lengths, including leap years, from January 2000 to December 2039.
2411-5
high speed.
recorded images in watch memory.