Casio 2411 Podręcznik - Strona 7

Przeglądaj online lub pobierz pdf Podręcznik dla Oglądaj Casio 2411. Casio 2411 9 stron.

Drukuj stronę

STOPWATCH

The stopwatch lets you measure elapsed time,

Mode

split times, and two finishes.

indicator

Hours

• The display range of the stopwatch is 23

hours, 59 minutes, 59.9 seconds.

• The stopwatch continues to run, restarting

STW

from zero after it reaches its limit, until you

‰H

‰ ‰

stop it.

• The stopwatch measurement operation

‰

continues even if you exit the Stopwatch

Mode.

1/10

• All of the operations in this section are

Minutes

seconds

performed in the Stopwatch Mode, which

Seconds

you enter by pressing D.

To measure times with the stopwatch

Elapsed Time

Start

Stop

Split Time

Start

Split

Two Finishes

Start

Split

First runner finishes.

Display time of first

runner.

POWER SUPPLY

About the Pre-installed Battery

The battery installed at the factory discharges during shipment and inventory

storage. Because of this, it may not provide the normal battery life specified

for this watch.

• It is up to you to purchase a battery for replacement, even if the battery you

are replacing does not last for the specified battery life period.

Low Battery Indication

As the battery goes low, the watch gradually disables functions to conserve

remaining power, as described below.

Step 1

The low battery indicator flashes on the display

Low battery indicator

when battery power drops below a certain

level. At this time, the following functions

become disabled.

' ‰ 1 6 - 3 ‰

• Entry to the Camera Mode

SAT

1 ‰ : 5 8

• VISUAL DATABANK Mode text input and

image data deletion

• IR Mode data communication

Step 2

If you do not replace the battery within about 24 hours, the low battery

indicator stops flashing and remains on the display and the following function

also becomes disabled.

• Daily alarm and countdown timer alarm sound (only the screen image

flashes)

Note

• Attempting to access any of the disabled

functions listed in Step 1 and Step 2 above

WAIT

causes the message LOW BATT to appear

LOW

and let you know that the function is not

BATT

available due to low battery power.

• The LOW BATT message remains on the

display for about one second.

• When the IR COM LOW BATT message

IR COM

appears when you enter the IR Mode,

LOW

pressing D exits the message screen.

BATT

Note that CASIO shall not be held responsible for any damage or loss,

including but not limited to lost profits, by you or any third party due to

data deletion or modification due to malfunction, repairs, battery

replacement, etc.

Battery Precautions

Incorrectly using a battery can cause it to burst or leak, possibly damaging

the interior of the watch. Note the following precautions.

• This watch is powered by a single CR-2032 lithium battery.

Re-start

Stop

Clear

Split release

Stop

Clear

Stop

Split release

Clear

Second

Display time of

runner

second runner.

finishes.

• We strongly urge that you use only the type of battery specifically

recommended in this manual.

• Damage to or dirt, dust, moisture on the inside of the battery cover and the

battery compartment or on the surface that comes into contact with the

rubber seal (gasket) can cause loss of water resistance. Keep such areas

clean and free of moisture.

• Never leave a dead or weak battery in the battery compartment. Doing so

runs the risk of damage and malfunction due to battery fluid leaks.

• Be sure to dispose of old batteries according to the local laws and

regulations in your area.

• Improperly replacing the battery can result in damage to the watch.

Repairing such damage will be charged to you, so take care to replace the

battery correctly.

• Never try to take the battery apart, or expose it to heat or direct flame.

Take care that the positive and negative ends of the battery never become

shorted.

• The battery installed at the factory is not rechargeable. Never try to charge it.

• Should battery fluid ever leak inside the battery compartment, immediately use

a dry rag to wipe it out while taking care not to get any fluid on your hands.

Keep batteries out of the reach of small children. If accidentally

swallowed, immediately contact a physician.

To replace the battery

1. Open the battery cover.

Rotate to

• Insert a coin or other similar object into

this point to

open.

• Do not use undue force when rotating

Battery cover

2. Remove the old battery.

Gasket

• If you have trouble removing the battery,

• Take care that you do not lose the

• Keep your fingers away from the spring

Spring

Battery

compartment

Inside of battery cover

3. Load a new battery

Gasket

• Wipe the surfaces of a new battery with

• Never pick up the battery with tweezers

• If the gasket comes out when you

• Whenever replacing the gasket, make

Battery cover

• Note the triangular shape of the gasket

Gasket

4. Close the battery cover.

Rotate to

• Replace the battery cover, and rotate it

this point to

close.

Settings Following Battery Replacement

The watch retains image data in memory when you replace the battery.

However, the current time, date, alarm settings, and countdown start time are

all cleared. Be sure you make these settings each time you replace the

battery.

2411-7

the slot in the battery cover and rotate

the cover to the OPEN position.

the battery cover. Doing so can damage

the cover.

try turning the back of the watch

downwards so it falls out.

battery compartment gasket.

inside the battery compartment. The

sharp edges of the spring create the risk

of personal injury.

a dry cloth, and load the battery into the

watch with its plus (+) side facing up (so

you can see it).

contacting the top surface and bottom

surface at the same time. Doing so

creates a short.

remove the battery, be sure to replace it

before loading the battery. You will not

be able to load the battery properly if the

gasket is not in place.

sure there is not dust or dirt on it.

material. The flat surface (the base of

the triangle) is the bottom, which should

be against the watch body when the

gasket is installed. The pointed surface

(the peak of the triangle) is the top,

which contacts the battery cover.

to the CLOSE position using a coin or

other similar object.